Titgemeyer MS 60 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 37

background image

24

Maintaining the riveting tool

H
E

Adjusting the jaw case body

In order to enable the riveting tool to travel an adequate stroke, the gap
between the jaw case (14) and hydraulic housing (3) must be adjusted
correctly.

• Detach the compressed air supply.

Caution

Hazard of injury by means of bruises or cuts in case of
unchecked cutting stroke! Always detach compressed air
supply before unscrewing the nose cap (2).

Attention

Material damage! Do not let O-ring (19) get damaged. If the
O-ring has been damaged, replace immediately.

• Loosen the nose cap (2) with wrench SW22, then unscrew it and

carefully pull it off the jaw case body (18).

• Measure the gap X at the nose cap (2) (as per diagram). For standard

measurements, X = 108 mm.

• Measure the distance between the jaw case (14) on the facing side and

the hydraulic housing (3) on the facing side; the correct distance
measures up to X - 17 mm.

• Loosen the lock nut (20) from the jaw case body (18) using a wrench

SW17, till the jaw case body (18) can rotate freely.

• Adjust the jaw case body (18) (for left or right side revolutions), till the

distance of X - 17 mm is obtained.

• Screw the lock nut (20) against the jaw case body (18).
• Hold the jaw case body (18) in this position using a wrench SW17,

and tighten the lock nut (20) using a wrench SW17
(see page 25 “Table for torque values”).

2

X-17

3

20

18

14

X

2

«
...
22
23
24
25
26
...
»

Содержание MS 60






































Отзывы:

Нет отзывов

Похожие инструкции для MS 60

Бренд: GE Страницы: 5

Бренд: Makita Страницы: 4

Бренд: Makita Страницы: 5

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 12

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 13

Бренд: Swagelok Страницы: 6

Color Block PSU-05B

Бренд: Chroma Страницы: 2

Бренд: Max Страницы: 87

Бренд: TE Connectivity Страницы: 8

Бренд: Parkside Страницы: 80

Бренд: Unimac Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды