Titgemeyer MS 60 Скачать руководство пользователя страница 31

Страница: 31 / 37

Disposing of the riveting tool

Ensure that the hydraulic oil is inside the riveting tool. Dispose it off in an
environmentally friendly manner.
Send the riveting tool back to the manufacturer in it’s original packing, if
still available.

Technical data

Type of riveting tool:

MS 60

Height:

340 mm

Width:

320 mm

Weight:

2,6 kg

Operating pressure:

5-7 bar

Compressed air supply
Nominal diameter:

DN 6

Power output (at 6 bar):

ca. 17,8 kN

Operating stroke:

ca. 26 mm

Operating range:

Blind rivet-shaft Diameter 4.0 to 6.4 mm

Sound emission level
in the workplace:

PAI

<70dB(A)

Vibration level:

<2,5m/s

If desired, the nose cap (2) can also be counted in other measure
ments.

The length and height and weight measurements of the riveting tool are
as per the standard procedures.

320 mm

340 mm

Содержание MS 60






































Результаты поиска

Содержание MS 60

Отзывы:

Похожие инструкции для MS 60

Бренды по названию

Популярные бренды

Titgemeyer MS 60, Руководство по эксплуатации

Результаты поиска

Содержание MS 60

Отзывы:

Похожие инструкции для MS 60

Бренды по названию

Популярные бренды