manualshive.com logo in svg

Tissue-Tek TEC 5100, Руководство по эксплуатации

Поделиться
Скачать
Tissue-Tek TEC 5100 Скачать руководство пользователя страница 10

2.2

Revised 07/12/11

UNPACKING,

SYSTEM DESCRIPTION

SYSTEM DESCRIPTION

Embedding Module

(FRONT PANEL)

Paraffin Chamber –

holds up to four liters of

molten paraffin; fine mesh filter at bottom of
chamber catches debris; can be set to any tem-
perature at or between 50°–75°C (122°–167°F);
factory set at 62°C (143.6°F).

Power Switch –

turns the power to the module

ON or OFF; circuit breaker.

Control Panel –

consists of an LCD display and

keypads (each component discussed in detail
later in this section). 

(Optional) Electric Forceps – (Connector
shown only) 

connects underneath the control

panel. Adjustable to 5 different temperature lev-
els.

Forceps Warmer Holders –

hold forceps; can

be set to any temperature at or between
50°–75°C (122°–167°C) using the Hot Plate
temperature settings; factory set at 62°C (149°F).

 

Paraffin Dispenser –

molten paraffin is dis-

pensed here; press fingerplate to dispense paraf-
fin or use the optional foot pedal; turn knob
“clockwise” to 

decrease flow

or “counterclock-

wise” to 

increase flow.  

Optional foot pedal 

(not

shown)

can be used instead of the fingerplate to

dispense paraffin.

Work Light –

increases visibility in hot plate

area making tissue positioning easier. 

(Optional) Magnifying Lens Assembly –

increases visibility while positioning tissue.

 

Содержание TEC 5100











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды