background image

MANUFACTURING COMPANY

OWNER’S WARRANTY

The 

Versalift

 Aerial Platform Lift is engineered and designed to perform as stated on

published  specifications.    Only  quality  material  and  workmanship  are  used  in  the

manufacture of this product.  With proper installation, regular maintenance, and periodic

repair service, the equipment will provide excellent service.

Those parts of the 

Versalift

 that are manufactured by 

Time Manufacturing Company

are warranted for one full year from date of purchase.  Structural components will carry

a lifetime warranty for defects in material and workmanship which existed at the time of

initial delivery, wear components are not covered by this statement.  This warranty is

issued only to the original purchaser and promises that 

Time Manufacturing Company

manufactured  products  are  free  from  defects  in  material  and  factory  workmanship

when properly installed, serviced, and operated under normal conditions, according to

the  manufacturer’s  instructions.

Manufacturer’s obligation under this warranty is limited to correcting without charge at

its factory any part or parts thereof which shall be returned to its factory or one of its

Authorized Service Stations, transportation charges prepaid, within one year after being

put into service by the original user, and which upon examination shall disclose to the

Manufacturer’s satisfaction to have been originally defective.  Correction of such defects

by repair to, or supplying of replacements for defective parts, shall constitute fulfillment

of all obligations to original user.

This  warranty  shall  not  apply  to  any  of  the  Manufacturer’s  products  which  must  be

replaced because of normal wear, which have been subject to misuses, negligence or

accident, or which shall have been repaired or altered outside  of the Manufacturer’s

factory  (unless  authorized  by  the  Manufacturer  in  writing),  products  which  have  not

been  maintained  and  operated  in  accordance  with  Time  Manufacturing  Company’s

operators,  maintenance  manuals  and  bulletins,  products  which  are  repaired  without

using  original  Time  Manufacturing  Company    parts.    This  limited  warranty  does  not

cover  transportation  fees  and/or  consumables  used  for  the  repair.    Products or parts

manufactured by others are covered only by such warranties as are extended to TIME

MANUFACTURING CO. by its suppliers.

Manufacturer shall not be liable for loss, damage, or expense directly or indirectly from

the use of its product or from any cause.

The  above  warranty  supersedes  and  is  in  lieu  of  all  other  warranties,  expressed  or

implied, and of all other liabilities or obligations on part of Manufacturer.  No person,

agent, or dealer is authorized to give any warranties on behalf of the Manufacturer or to

assume for the Manufacturer any other liability in connection with any of its products

unless made in writing and signed by an officer of the Manufacturer.

Содержание Versalift SST-37-EIH




















































Отзывы: