Time Versalift SST-37-EIH, Руководство оператора

Страница: 20 / 51

3-2
28009-09 09/16 VERSALIFT SST-37/40-EIH
SPECIFICA
TIONS
PEDESTAL - The pedestal is a round shape with an
access opening on both sides. The 12 gallon (45 l)
hydraulic reservoir is built integral to the pedestal. A
100-mesh suction screen and 10-micron return line
fi lter are located inside the pedestal. The top plate is
1-1/4 in. (32 mm) thick and machined fl at to support
the rotation bearing.
LUBRICATION - Non-lube bearings are used at all
points of motion. The rotation bearing is the only
component that requires periodic lubrication.
PAINTING - The complete unit is primed and painted
prior to assembly. The standard color is white
urethane.
HYDRAULIC OIL RESERVOIR - Designed as an
integral part of the pedestal, the reservoir has an
anti-splash baffl e and easy to read fl uid level gages.
The oil capacity of the reservoir is 12 gallons (45 l),
which is suffi cient for a 5 GPM (19 lpm) hydraulic
tool circuit.
HYDRAULIC SYSTEM - The open-center hydraulic
system operates at 3 gpm (11.4 lpm) at 2250 psi
(158 kg/cm
2
). The pump draws oil through a 100-
mesh suction screen. A 10-micron return line fi lter
with bypass valve is included. Fluid level gages are
furnished for checking fl uid level. Hydraulic oil is not
included. This system can be driven by the chassis-
engine accessory belt or by the chassis transmission
power-take-off .
HOSES AND FITTINGS - The hoses routed through
the booms are high pressure and non-conductive with
swaged hose end fi ttings. Nylon sleeves are installed
over hoses at points of movement. Reusable fi ttings
can be installed if a hose is damaged.
ENGINE START/STOP AND MASTER CONTROL
- The start/stop circuit has been designed so that
the lift cannot be operated unless the truck ignition
key is in the “run” position and the master switch is
“on.” This feature makes it diffi cult for unauthorized
individuals to operate the lift when the truck is locked.
An air cylinder at the platform and a toggle switch at
the turret are provided to actuate the engine start/
stop control.
ELECTRICAL INSULATION SPECIFICATIONS
- The outer/inner boom assembly is tested and
certifi ed for electrical work at 46 KV and below in
accordance with ANSI A92.2 requirements. Aerial
devices may be designed and confi gured for gloving
work and tool methods at 46KV and below. The
outer/inner boom assembly is fully insulated even
in a retracted position.
OUTRIGGER BOOM INTERLOCK SYSTEM -
The outrigger/boom interlock system is a feature
designed to prevent the lift from being operated until
the outriggers contact the ground. The interlock also
prevents the outriggers from being retracted before
the lower boom is properly stored.
SLOPE INDICATORS – Slope indicators are
required on Versalift units and supplied by Time
Manufacturing Co. Slope indicators shall be installed
to indicate the level of rotation bearing relative to
the ground.
MANUALS - Two Operator’s Manuals and two
Service Manuals, one Manual of Responsibilities
and one EMI Safety Manual are included with each
aerial lift.
SST-EIH OPTION SPECIFICATIONS
Below is a brief description of some of the available
options for the aerial lift.
INDEPENDENT H-FRAME OUTRIGGERS -
Outriggers are shear-plate mounted to the frame
and are equipped with pilot operated check valves,
internal thermal relief valves and separate controls.
The outriggers furnish 90 1/2 in. (2.3 m) of spread
and a maximum of 9 in. (.23 m) of penetration with
15 in. (.38 m) of ground clearance. Outrigger legs
are shipped loose to accommodate various frame
heights and body widths. Outrigger pivot feet are
standard.
INDEPENDENT A-FRAME OUTRIGGERS -
Outriggers are shear-plate mounted to the frame
and are equipped with pilot operated check valves,
internal thermal relief valves and separate controls.
At maximum extension, the outriggers furnish 125
3/4 in. (3.19 m) of spread and 9 in. (229 mm) of
penetration. They have 17 in. (432 mm) of ground
clearance based on 36 in. (0.91 m) or 31 in. (0.79
m) frame height. Outrigger pivot feet are standard.
TORSION BAR - Over frame and under frame
torsion bars are available and add to the stability
of the vehicle. All Stable Ride torsion bars include
rubber bushings at all points of movement and do
not require lubrication. Ballast may be required with
the use of torsion bars.
TALLER AND SHORTER PEDESTALS - Pedestals
6 in. (152 mm) taller or 6 in. (152 mm) shorter are
available.
CONTINUOUS ROTATION - Rotation is continuous