Tianlong Gentier 48E Скачать руководство пользователя страница 19

Страница: 19 / 139

Gentier Real-Time PCR System

Caution

: the main control computer of the Gentier instrument is not designed for online use,

connect it to internet may cause risks of computer virus infection or hacker attacks.

XATL Co.,

LTD.

will not be responsible for

any damages caused by.

Caution

: it is not recommended to install other software on the main control computer of the

Gentier instrument. Otherwise there may be potential risks of software module conflict, and

may also influences the results reliability.

Caution

XATL Co., LTD.

will not provide anti-virus software. Therefore, if necessary, please

take preventive measures to prevent the main control computer from virus.

3.1.3 Instrument Characters

▶

Touch Screen Operation

: Gentier instrument possesses a built-in 7.0

’

-inches colored touch

screen, very easy for operation. It can run independently from the computer;

▶

Independent Temperature Control

: Gentier instrument adopts independent temperature

control technology and high repeatability temperature zone. Truly realize the optimization
of PCR;

▶

Power-off Protection

: Gentier instrument possesses instantaneous power-off protection

function which can protect all configuration settings in case of power off and the interrupted
experiment can continue after power on.

▶

Multiple PCR Step Modes

: Gentier instrument provides multiple PCR step modes, such as

touchdown step, long step, gradient step, melting step and so on.

Reminding

: the Gentier 48S instrument model cannot support gradient PCR step mode.

▶

Remote Running

: user could edit experiment settings on control computer and command

the connected Gentier instrument, truly realize the remote running control and real-time
monitoring.

▶

Lis System

: Gentier instrument can be connected to hospital Lis system.

3.2 Software Characters

▶

Software Interface

: wizard-style interface, intuitive layout and program setting, very easy

for operation.

Содержание Gentier 48E












































































































































Результаты поиска

Содержание Gentier 48E

Отзывы:

Бренды по названию

Популярные бренды

Tianlong Gentier 48E, Руководство пользователя

Результаты поиска

Содержание Gentier 48E

Отзывы:

Бренды по названию

Популярные бренды