Tianlong Gentier 48E Скачать руководство пользователя страница 129

Страница: 129 / 139

115

Gentier Real-Time PCR System

2.5.3 Service Sub-tab

Figure E-6.3 General Setting tab - Service sub-tab

Introduction to Service sub-tab

▶

Lock Instrument for Transportation

: user can press

< Lock >

and the system software will

guide the operator to lock the transport lock.

For detailed installation steps of transport,

please refer to

F-3.2 Install the Transport Lock

▶

Clear Memory

: user can press

< Clear >

to clear all experiment files.

▶

DebugLog

: user could connect an USB drive to the Gentier instrument and press press

< Get

DebugLog >

to download all the log file of the current Gentier instrument, this will help our

professional engineer to get the relative information in case the instrument require
maintenance.

▶

Build No.

: user could press

< Details >

to view the build number of the current instrument.

▶

Debug Mode

: press

< Enter Debug Mode >

and input the password, the instrument software

will pop up the debug interface.

Reminding

: no person except the professional engineers from our company is allowed to

enter the debug mode.

Содержание Gentier 48E












































































































































Результаты поиска

Содержание Gentier 48E

Отзывы:

Бренды по названию

Популярные бренды

Tianlong Gentier 48E, Руководство пользователя

Результаты поиска

Содержание Gentier 48E

Отзывы:

Бренды по названию

Популярные бренды