manualshive.com logo in svg

THORLABS TPA101, Руководство пользователя

Поделиться
Скачать
THORLABS TPA101 Скачать руководство пользователя страница 17

17

T-Cube Position Aligner

3.3.4

Using The USB Controller Hub

The TCH002 USB Controller Hub provides power distribution and USB comms for up
to six T-Cubes. It requires only a single power connection and a single USB
connection to the host PC. Further details are contained in handbook 

ha0146T  T-

Cube Controller Hub

, supplied with the unit.

Caution

If an external power supply is used, ensure that the 3 supply voltages are 

turned on and off simultaneously. Applying the supply voltages with a 

large (more than 1 second) time delay between them can result in the 

position aligner cube showing an incorrect reading.

Warning

DO NOT PLUG A POWERED UP T-CUBE INTO THE TCH002 USB 

CONTROLLER HUB. Always ensure that all power is disconnected from 

the Controller T-Cubes AND the hub before the T-Cube is plugged into the 
hub. Failure to observe this precaution will seriously damage the T-Cube 

unit and could result in personal injury.

Caution - T-Cube Hub Signal Routing (Revision 2 units or later).

  The T-Cube Hub allows the transfer of voltage signals between T-Cubes 

with two available analog lines. This is used by the TPZ001 Piezo Cube 

and TSG001 Strain Gauge Cube to route a feedback signal via the Hub for 
closed loop operation. It is also used by the TPA101 position aligner Cube 

to send position demand signals to a pair of slave revision 2 TPZ001 

Piezo Cubes (firmware version 2.0.X). The firmware version is displayed 

on power up.

A clash can occur if a TSG001 Strain Gauge Cube and a TPA101 position 
aligner Cube are combined on the hub, and both attempt to drive voltage 

signals out via the Hub. In this instance it is recommended that the 

TPA101 position aligner Cube is configured to drive signals out via its 

SMA connections and the associated TPZ001 Piezo Cube pair configured 

to pick these signal up via SMA inputs. This will require small SMA to 

SMA connection cables (e.g. CA2912), various lengths of which are 

available from Thorlabs

Caution

The TCH002 hub cannot be used to communicate between Revision 1 

(firmware version 1.0.X) TPZ001 Piezo T-Cube units and the TPA101 

position aligner T-Cubes. However, the hub may be used to supply power 
to each unit in the system. The firmware version is displayed on the piezo 

units, immediately after power up.

Содержание TPA101









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды