THERMOROSSI CIAO Скачать руководство пользователя

Страница: 12 / 40

Pg. 12

• The two digits representing the minutes will be turn on. Press button (3) or (4) to enter the minutes of the first cycle start time. To
confirm the selection press the button (1).
• The first start up time for Monday has now been set.
Then the inscription OFF1 will appear in the display and the two digits representing the hours will turn on. Press button (3) or (4) to
enter the time for the first shut off. To confirm the selection press the button (1).
• The two digits representing the minutes will be turn on. Press button (3) or (4) to enter the minutes for the first shut off. To confirm
the selection press the button (1).
• At this point the first on-off cycle for Monday has been entered.
Later,  it  is  possible  to  set  the  Monday’s  second  and  third  on-off  cycle  (shown  with  the  display  of  On2  and  OFF2)  and  the  third
Monday’s  on-off  cycle  (shown  with  the  display  On3  and  OFF3).  Inside  the  programming  menu,  if  for  example  the  Wednesday’s
programming is to be changed, go to the third green led by pressing key (2): then edit the on-off program times for Wednesday and
confirm  by  pressing  button  (6).  If  the  second  on-off  cycle  is  not  required  simply  set  the  On2  time  as  00:00  and  the  Off2  time  as
00:00 .
•  To  end  the  programming  process  press  button  (6)  several  times  or  exit  the  programming  menu.  To  enable  or  disable  the
programming  process  press  button  (5);  the  programming  is  enabled  when  on  cr  appears  on  the  display  and  the  steady  LED
appears in the bottom right corner of the display; programming is disabled when the of cr appears momentarily on the screen and
the LED in the bottom right corner of the display goes off. This function activates or deactivates the settings programmed for the
week. When the programming is active the operating conditions at ignition (combustion level – ventilation speed) are the same as
those set before the last shut down, but only if the shut down occurred through programming, that is, not manually.
Caution: in case the off-cycle (if carried out while the heater cycle is being controlled by the programming) is activated manually, at
the  next  start  up  controlled  by  the  programming  the  heater  will  be  set  at  the  1st  combustion  power  level  and  the  1st  ventilation
speed.
• In order to display the present time and programmings, key (6) must be repeatedly pressed until the current time is displayed.
Press button (3) or (4) to view all the programming values: to exit press button (6) twice. CAUTION: to change the programming day
press button (3) or (4) 6 times in succession.
• If you wish to start the heater after a programmed shut down, disable the CHRONO and press button (1) several times.

In the event of a programmed cycle on always ensure that the brazier is clean and seated correctly in its lodging:
failure to clean the brazier can reduce the life of the spark plug and be a hazard for the user.

When the programming is enabled (temporary inscription on cr on the display and, at the same time, a fixed LED is
present on the right side at the bottom of the display) any additional chronothermostat (see para. 7.2) is deactivated.

5.4 OPERATING LEVEL SETTING

The heater must be fed with the rear switch in position "1".
Display (7) may show the inscriptions On, OFF or Star.

The appliance has an inbuilt program optimised to favour combustion efficiency; this program appears on the display with P 1.
However,  if  you  use  poor  quality  pellets  which  have  different  combustion  residues  compared  to  those  that  comply  with  current
regulations, it is possible to select other pre-programmed combustion levels.
P 2: is an operating program that increases the speed of the smoke suction unit. This program increases the air flow to the burner
to improve combustion of more tightly compacted wood pellets: When P 2 is selected, the combustion efficiency could drop.
P 0: this program is useful when using pellets that are too long and/or flue outlets with very high vacuum, over  2 mm water column.

To modify the program, proceed as follows:
• press three times the key (6) until the inscription LIV flashes on the display and, then, the corresponding level set on the heater
will show ( P1 or P2 or P0)