Thermo Scientific Vanquish Charger Скачать руководство пользователя страница 7

Страница: 7 / 47

•

Installation

Solvent Monitor
Installation Guide

Page 7

Installation

3.1

Scope of Delivery

The following items are included in the delivery:

•

Solvent monitor

•

Ship Kit

•

Installation Guide

For information on contents of the ship kit or reordering parts, see

Consumables and Replacement Parts (

}

page 46)

3.2

Rating Plate

The rating plate is located on the rear side of the solvent monitor. The
rating plate indicates the serial number, part number, module name,
revision number (if any), line rating, and the manufacturer's address.

3.3

Allowed Concentrations

The allowed salt concentration for the solvent monitor is 1 mol/L or less.

NOTICE

If the solvent monitor is used in a Vanquish Core system, observe the
lower chloride concentration allowed for this system (refer to the

Vanquish System Operating Manual

Содержание Vanquish Charger
















































Результаты поиска

Содержание Vanquish Charger

Отзывы:

Похожие инструкции для Vanquish Charger

Бренды по названию

Популярные бренды

Thermo Scientific Vanquish Charger, Руководство по установке

Результаты поиска

Содержание Vanquish Charger

Отзывы:

Похожие инструкции для Vanquish Charger

Бренды по названию

Популярные бренды