Thermo Scientific ULTROpure 682 Series Скачать руководство пользователя страница 44

Страница: 44 / 44

One Year Limited Warranty

This Thermo Scientific product is warranted to be free of defects in materials and workmanship for one (1)

year from the first to occur of (i) the date the product is sold by the manufacturer or (ii) the date the product is

purchased by the original retail customer (the “Commencement Date”). Except as expressly stated above, the

MANUFACTURER MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, WITH RESPECT TO THE

PRODUCTS AND EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES, INCLUDING BUT NOT LIMITED

TO, WARRANTIES OF DESIGN, MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

An authorized representative of the manufacturer must perform all warranty inspections. In the event of a

defect covered by the warranty, we shall, as our sole obligation and exclusive remedy, provide free replace-

ment parts to remedy the defective product. In addition, for products sold within the continental United States

or Canada, the manufacturer shall provide free labor to repair the products with the replacement parts, but

only for a period of ninety (90) days from the Commencement Date.

The warranty provided hereunder shall be null and void and without further force or effect if there is any (i)

repair made to the product by a party other than the manufacturer or its duly authorized service representa-

tive, (ii) misuse (including use inconsistent with written operating instructions for the product), mishandling,

contamination, overheating, modification or alteration of the product by any customer or third party or (iii) use

of replacement parts that are obtained from a party who is not an authorized dealer of Thermo Scientific prod-

ucts.

Heating elements, because of their susceptibility to overheating and contamination, must be returned to the

factory and if, upon inspection, it is concluded that failure is due to factors other than excessive high tempera-

ture or contamination, the manufacturer will provide warranty replacement. As a condition to the return of any

product, or any constituent part thereof, to the factory, it shall be sent prepaid and a prior written authorization

from the manufacturer assigning a Return Materials Number to the product or part shall be obtained.

IN NO EVENT SHALL THE MANUFACTURER BE LIABLE TO ANY PARTY FOR ANY DIRECT, INDIRECT,

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OR FOR ANY DAMAGES RESULTING FROM

LOSS OF USE OR PROFITS, ANTICIPATED OR OTHERWISE, ARISING OUT OF OR IN CONNECTION

WITH THE SALE, USE OR PERFORMANCE OF ANY PRODUCTS, WHETHER SUCH CLAIM IS BASED ON

CONTRACT, TORT (INCLUDING NEGLIGENCE), ANY THEORY OF STRICT LIABILITY OR REGULATORY

ACTION.

For the name of the authorized Thermo Scientific product dealer nearest you or any additional information, contact us:

2555 Kerper Blvd., Dubuque, Iowa, 52004-0797

Phone: 563-556-2241 or 1-800-553-0039

Fax: 563-589-0516

Web: www.thermo.com

Содержание ULTROpure 682 Series













































Результаты поиска

Содержание ULTROpure 682 Series

Отзывы:

Похожие инструкции для ULTROpure 682 Series

Бренды по названию

Популярные бренды

Thermo Scientific ULTROpure 682 Series, Руководство по эксплуатации

Результаты поиска

Содержание ULTROpure 682 Series

Отзывы:

Похожие инструкции для ULTROpure 682 Series

Бренды по названию

Популярные бренды