background image

Troubleshooting & Support 

Contact Information 

Contact 

Information 

The local representative is the first contact for support and is well equipped 
to answer questions and provide application assistance. Your representative 
also has access to product information and current software revisions. You 
can also contact Thermo Fisher directly. 

In the United States 

 

In Canada 

 

 

Thermo Fisher Scientific 

1410 Gillingham Lane 

Sugar Land, TX 77478 

Phone: 713-272-0404 

Fax: 713-272-2272 

 

Thermo Fisher Scientific 

14 Gormley Industrial Avenue 

Gormley, Ontario 

L0H 1G0 

Phone: 905-888-8808 

Fax: 905-888-8828 

In Europe 

 

On the Web 

 

 

Thermo Fisher Scientific 

Ion Path  

Road Three  

Winsford  

Cheshire CW7 3GA  

United Kingdom  

Phone: +44 (0) 1606 548700 

 www.thermo.com 

 

Warranty 

Thermo Scientific products are warranted to be free from defects in 
material and workmanship at the time of shipment and for one year 
thereafter. Any claimed defects in Thermo Scientific products must be 
reported within the warranty period. Thermo Fisher shall have the right to 
inspect such products at Buyer’s plant or to require Buyer to return such 
products to Thermo Fisher’s plant.  

In the event Thermo Fisher requests return of its products, Buyer shall ship 
with transportation charges paid by the Buyer to Thermo Fisher’s plant. 
Shipment of repaired or replacement goods from Thermo Fisher’s plant 
shall be F.O.B. Thermo Fisher plant. A quotation of proposed work will be 
sent to the customer. Thermo Fisher shall be liable only to replace or 
repair, at its option, free of charge, products which are found by Thermo 
Fisher to be defective in material or workmanship, and which are reported 
to Thermo Fisher within the warranty period as provided above. This right 
to replacement shall be Buyer’s exclusive remedy against Thermo Fisher. 

Thermo Fisher shall not be liable for labor charges or other losses or 
damages of any kind or description, including but not limited to, 
incidental, special or consequential damages caused by defective products. 
This warranty shall be void if recommendations provided by Thermo 

6-4

     STD5000 & STD6000 User Guide 

Thermo Fisher Scientific 

Содержание STD5000













































Отзывы: