Thermo Scientific Sorvall LYNX 4000 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 72

background image

P

Preface

Intended Purpose

iv

Sorvall LYNX 4000 / 6000

Thermo Scientific

Intended Purpose

•

This centrifuge is a laboratory product designed to separate components by generation of a relative
centrifugal force. It separates human samples (e.g. blood, urine and other body fluids) collected in
appropriate containers, either alone or after addition of reagents or other additives.

•

As research laboratory or bioprocessing laboratory centrifuge, it is designed to also run other
containers filled with chemicals, environmental samples and other non-human body samples.

•

Maximum sample density at maximum speed: 1.2

•

This centrifuge should be operated by trained specialists only.

Symbols used in this Manual

Symbols used on the Centrifuge

g

cm

3

-----------

This symbol refers to general hazards.

CAUTION

means that material damage could occur.

WARNING

means that injuries or material damage or contamination could occur.

This symbol refers to biological hazards.

Observe the information contained in the instruction manual to keep yourself and your
environment safe.

This symbol refers to electrical hazards.

This symbol refers to general hazards. Follow the instructions in the instruction manual in
any case.

This symbol refers to information on hazards, described within the manual.

This Symbol refers to check, if the rotor is installed correct by lifting it slightly at
the handle. See

“Rotor Installation”

«
...
4
5
6
7
8
...
»

Содержание Sorvall LYNX 4000









































































Отзывы:

Нет отзывов

Похожие инструкции для Sorvall LYNX 4000

Бренд: ZOLL Страницы: 84

Бренд: Kaivac Страницы: 29

Бренд: MacDon Страницы: 65

Бренд: Hanil Страницы: 60

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: QBC Diagnostics Страницы: 65

Coronis 5MP Mammo

Бренд: Barco Страницы: 4

Бренд: Barco Страницы: 167

Color Coronis 2MP

Бренд: Barco Страницы: 156

Color Coronis 2MP

Бренд: Barco Страницы: 12

Бренд: Barco Страницы: 39

Бренд: Barco Страницы: 158

Бренд: Bard Страницы: 36

Бренд: Bard Страницы: 2

Бренд: Bard Страницы: 30

Бренд: Bard Peripheral Vascular Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды