Thermo Scientific Sorvall LYNX 4000 Скачать руководство пользователя страница 39

Страница: 39 / 72

Operation

Entering Parameters

Thermo Scientific

Sorvall LYNX 4000 / 6000

Touch the number of the desired profile or move the slider by sliding your fingers over the numbers.
Select

Apply

to confirm this selection for the next run.

The profile with the lowest number has the shallowest incline marked with

min

; profile number 9 is the

steepest incline which is marked with

max

Preselecting Speed / RCF-Value

1. Press

The following screen appears:

Figure 11.

Screen for Speed and RCF-Value

2. Press

rpm

rcf

depending on the value you would like to change. The selected function is

highlighted in yellow.

3. Enter the desired value using the numeric pad.

The digits show in sequential order.

4. Confirm your entry by pressing

Confirm

Note

If an extremely low or high speed or RCF-value has been selected, a message will appear with

the permissible values.

Содержание Sorvall LYNX 4000









































































Результаты поиска

Содержание Sorvall LYNX 4000

Отзывы:

Похожие инструкции для Sorvall LYNX 4000

Бренды по названию

Популярные бренды

Thermo Scientific Sorvall LYNX 4000, Инструкция по эксплуатации

Результаты поиска

Содержание Sorvall LYNX 4000

Отзывы:

Похожие инструкции для Sorvall LYNX 4000

Бренды по названию

Популярные бренды