Thermo Scientific Haas Mini Mill Скачать руководство пользователя страница 19

Страница: 19 / 68

Machine Operation

Chapter 2

AA83766

User Manual - Haas Mini Mill

Stop Procedure

♦

Press on the

POWER OFF

function touch of the Simatic mobile panel to switch off the AMP (#5 or

(

on figure 2.1).

♦

Press on the

POWER OFF

button of the Haas panel (#4 on the Haas panel above).

Powering Up the PM

♦

Switch the Haas

MAIN POWER

switch

Figure 2.3

♦

Open the PrepControl cabinet and check that all circuit breakers are switched ON.

♦

Press on the

POWER ON

button on the Haas panel (#3 on figure 2.2).

♦

Press on the

POWER ON

function touch of the Simatic mobile panel to switch on the AMP (#6 or

)

on figure 2.1).

♦

On the Haas Control Panel, press on the

RESET

button (#9 on figure 2.2) until no error are displayed.

♦

Open and close the Operator Door as instructed on the screen.

♦

Press on

POWER UP – RESTART

(#10 on figure 2.2), this will initialize the XYZ axis.

♦

On the Simatic mobile panel go in

SYSTEM 2/4 : Users

and log yourself in with the

SERVICE

account.

♦

If the machine wasn’t used for more than 4 days, you will need to launch the Spindel Warm-up program.

To do so follow this procedure:

♦

SERVICE

mode

♦

Go in

MEM

mode

♦

You can start to work.

One general rule: do not switch on the power immediately after having switched it off

Содержание Haas Mini Mill





































































Результаты поиска

Содержание Haas Mini Mill

Отзывы:

Похожие инструкции для Haas Mini Mill

Бренды по названию

Популярные бренды

Thermo Scientific Haas Mini Mill, Руководство пользователя

Результаты поиска

Содержание Haas Mini Mill

Отзывы:

Похожие инструкции для Haas Mini Mill

Бренды по названию

Популярные бренды