Thermo Scientific Haas Mini Mill Скачать руководство пользователя страница 18

Страница: 18 / 68

Chapter 2

Machine Operation

User Manual - Haas Mini Mill

AA83766

Haas Mini Mill Control Panel

Only the commands needed for operation are described.

1.  Haas control panel
2.  Screen
3.  Power on button
4.  Power off button
5.  Emergency stop button
6.  Handle jog
7.  Cycle start button (Auto

mode)

8. Feed hold button (Auto

mode)

9. Reset button
10. Power up restart button
11. Memory mode button

12.

Handle mode button.

Figure 2.2

Start Up

This section describes the main commands in order to start up the machine.

Start Up Procedure

♦

The main power switch on the principal rack of the PM must be on.

♦

Press on the

POWER ON

button of the Haas panel (#3 on the Haas panel above).

♦

Remove all ES that could be on.

♦

Wait that the ARL SMS mobile panel screen shows

MILLING 1/2 : ROBOT

♦

Press on the

POWER ON

function touch of the Simatic mobile panel to switch on the AMP (#6 or

)

on figure 2.1).

♦

Press on the

RESET

button as long as you have alarm message on the screen of the Haas panel (#9 on

the Haas panel above).

♦

Do a cycle door (open/close) of the PM.

♦

Press on the

POWER UP - RESTART

button to put the PM in origins position (#10 on the Haas panel

above).

♦

Press on the

MEM

button to select the memory mode (#11 on the Haas panel above).

Содержание Haas Mini Mill





































































Результаты поиска

Содержание Haas Mini Mill

Отзывы:

Похожие инструкции для Haas Mini Mill

Бренды по названию

Популярные бренды

Thermo Scientific Haas Mini Mill, Руководство пользователя

Результаты поиска

Содержание Haas Mini Mill

Отзывы:

Похожие инструкции для Haas Mini Mill

Бренды по названию

Популярные бренды