Thermo Scientific DB-070 E Скачать руководство пользователя

Страница: 113 / 118

RadEye AB100

DB-070 E

12-9

Pi/Ff 04.05.2021

V 1.75

•

Scaler mode can be controlled remotely

•

Rounding error in measuring unit “cpm” and “dpm” fixed

•

Menu item “Display α/αβ” was disabled. Now it is visi-
ble again.

•

New function: “Alarm acknowledge” enable/disable. If

Alarm acknowledge is disabled the acoustic and vibration

alarm cannot be muted.

•

New function: Set alarm threshold to 3xbackground. Af-

ter background measurement the user is asked if the alarm

threshold for beta threshold should be set to

3xbackground count rate.

•

LED flash and a double beep at the end of a scaler meas-

urement.

•

Data set number is increased at the start of a scaler meas-

urement.

•

Lowest settable voltage: 100V. Before the voltage could

be set to 0V

•

New menu items “Display contrast” and “Language” in
sub menu “Settings”

•

Feature "beta window in activity mode" removed

•

A classic linear ratemeter filter can be selected instead of

ADF.

•

The ratemeter can be set to the actual value by a long
press on the “Menu/◄” button.

Содержание DB-070 E























































































































Результаты поиска

Содержание DB-070 E

Отзывы:

Похожие инструкции для DB-070 E

Бренды по названию

Популярные бренды

Thermo Scientific DB-070 E, Руководство по эксплуатации

Результаты поиска

Содержание DB-070 E

Отзывы:

Похожие инструкции для DB-070 E

Бренды по названию

Популярные бренды