Thermo Scientific AquaSensors AquaTrace Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 34

background image



Temperature measurement included



Can be connected to MODBUS, DeviceNET, Ethernet, USB, RS-232 and CANopen networks.

2.3 AV38 Remote Display

For detailed information on configuration of AV38 current outputs, relays, host communications,
please refer to the AV38 manual. This manual will describe basic calibration, configuration and

dissolved oxygen compensation functions directly related to dissolved oxygen measurements

The AV38 is a universal display interface for DataStick sensor systems that includes dissolved oxygen

measurement. The enclosure has ¼ DIN dimensions for easy mounting and is rated NEMA 4X for

outdoor use. It uses a liquid crystal display (LCD) with a high contrast backlight for best readability and

is powered with 24 volts DC or optionally with line power (90 VAC to 240 VAC).

The AV38 automatically recognizes the type of DataStick connected to the
system and provides the appropriate calibration, configuration and diagnostic

menus. It has options for two 4-20 current outputs, two alarm/control/wash
relays and network communications to a host computer. In addition, the AV38

can address up to 247 DataStick sensors.

Thermo Scientific AquaSensors

™

AquaTrace

™

Trace DO System User Guide

9

«
...
9
10
11
12
13
...
»

Содержание AquaSensors AquaTrace



































Отзывы:

Нет отзывов

Похожие инструкции для AquaSensors AquaTrace

Бренд: Landoll Страницы: 83

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: Faderfox Страницы: 8

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Yamaha Страницы: 178

Бренд: Yamaha Страницы: 15

Бренд: Panasonic Страницы: 23

Бренд: Interacoustics Страницы: 25

Retractable Box Scrapers HR3584

Бренд: Land Pride Страницы: 1

Бренд: Cablexpert Страницы: 12

Бренд: Rainbow Colour Changers Страницы: 22

Бренд: Simplicity Страницы: 20

Бренд: TOORX Страницы: 28

Бренд: Kärcher Страницы: 28

Бренд: Digilent Страницы: 14

Бренд: Fluke Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды