Thermo Scientific AquaPro Скачать руководство пользователя

Страница: 61 / 63

Thermo Scientific AquaPro Analyzer User Guide

14.5

Environmental Conditions



Ambient operating temperature range: -20 to 60 °C



Ambient storage temperature range: -20 to 70°C



Maximum Relative humidity: 95% non-condensing



Meets NEMA 4X requirements for outdoor use.



For industrial use.

14.6

Interchangeable Modules

Factory installed function cards can be reconfigured in the field. Slot 1:
pH,ORP,Conductivity,DO,Ozone,Turbidity,Chlorine,SS

Slot 2: pH,ORP,Conductivity,DO,Ozone,Turbidity,Chlorine,SS

Slot 3: pH,ORP,Conductivity,DO,Ozone,Turbidity,Chlorine,SS

Slot 4: pH,ORP,Conductivity,DO,Ozone,Turbidity,Chlorine,SS, Host Comms, 3 Optional relays.

Power: AC or DC

14.7

4 to 20 Milliamp Current Loops



Two isolated current loops per sensor (standard).



Setup as 0 or 4 to 20 mA.



0.01mA Resolution.



Each output assignable to sensor, temperature or Math.



Full featured PID control function w/ pH or conductivity.



Loop power provided by AquaPro

Содержание AquaPro
































































Результаты поиска

Содержание AquaPro

Отзывы:

Похожие инструкции для AquaPro

Бренды по названию

Популярные бренды

Thermo Scientific AquaPro, Руководство пользователя

Результаты поиска

Содержание AquaPro

Отзывы:

Похожие инструкции для AquaPro

Бренды по названию

Популярные бренды