Thermo Scientific AquaPro Скачать руководство пользователя

Страница: 50 / 63

Thermo Scientific AquaPro Analyzer User Guide

PID Functions

Use the UP/DOWN arrows to scroll the list of PID Controller options for viewing and editing.

Each of the PID options used to configure and tune the loop is shown below for a sensor type of pH.

PID Function

Edit Range

Default Setting

Set Algorithm

ISA or Velocity

ISA

Set Full-Scale

0 to 14 pH

14 pH (Do not change)

Set Zero-Scale

0 to 14 pH

0 pH (Do not change)

Set Setpoint

0 to 14 pH

7 pH

Set Proportional Gain

−

99.99 to +99.99

0.00 (+ is direct action,

−

is reverse action)

Set Integral Gain

0.00 to 50.00 reps/min

0.00 reps/min

Set Derivative Gain

0.00 to 10.00 seconds

0.00 seconds

Set Transit Time

0 to 9999 seconds

0 seconds

Set Man Reset

0.0% to 100%

0.0%

Manual Mode

Control: 0.0% to 100%

0.0% (Process value is displayed)

Scroll through these configuration and tuning options with UP/DOWN arrows. Press ENTER to select an option

and view or edit the setting. Press ENTER to change setting or ESC to leave a setting unchanged.

Note that in the Manual Mode, the present pH value is displayed in the top line and the Control Adjustment is

made in the second line.

≡

PID Controller

►

Set Algorithm

►

Set Full-Scale

►

Set Zero-Scale

►

Set Setpoint

►

Set Prop Gain

►

Set Integ Gain

►

Set Deriv Gain

►

Set Trans Time

►

Set Man Reset

►

Set Manual Mode

◄

Exit

Содержание AquaPro
































































Результаты поиска

Содержание AquaPro

Отзывы:

Похожие инструкции для AquaPro

Бренды по названию

Популярные бренды

Thermo Scientific AquaPro, Руководство пользователя

Результаты поиска

Содержание AquaPro

Отзывы:

Похожие инструкции для AquaPro

Бренды по названию

Популярные бренды