Thermo Scientific AquaPro Скачать руководство пользователя

Страница: 60 / 63

Thermo Scientific AquaPro Analyzer User Guide

14.2

Functions and Features



1 to 4 Sensors for optimal cost per measurement point.



Temperature measurement for all sensors (standard).



NEMA 4X Enclosure for indoor/outdoor use.



Wall, Pipe and ½ DIN Panel Mounting options.



Very readable large color graphics display.



Math Functions for % rejection, % pass and others.



Data and Event Logs for 4 channels for 30 days (Standard).



Front panel USB port for easy data log extraction, quick system configuration, field software upgrades.



Calibration, System Setup, Diagnostics and Service Menus.



Two 4 to 20 mA loop outputs per sensor (up to 8).



Three Form C Relays for Alarm, Control and Wash (Standard).



Option for six Form C Relays when up to 3 sensors are used.



Full Featured PID function for process control.



Digital protocol options for remote measurement, calibration, setup and diagnostics: Modbus,

Devicenet, Ethernet IP…



6 cable ports for standard conduit and cordgrip fittings.

14.3

Mounting Options



Wall Mount with Quick Disconnect mounting plate.



½ DIN Panel Mount.



Pipe/Hand rail mount (vertical and horizontal).

14.4

Interface



Display:

4.3 Inch Color Graphics with High Contrast



Keypad:

7 Key menu navigation

Содержание AquaPro
































































Результаты поиска

Содержание AquaPro

Отзывы:

Похожие инструкции для AquaPro

Бренды по названию

Популярные бренды

Thermo Scientific AquaPro, Руководство пользователя

Результаты поиска

Содержание AquaPro

Отзывы:

Похожие инструкции для AquaPro

Бренды по названию

Популярные бренды