Thermo Scientific Agilent 1200 Series Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 58

background image

2

Setting Up the LAN Interface

Setting the Stored TCP/IP Address for the LAN Interface

Thermo Scientific

Agilent 1200 Series Getting Connected Guide for LC Devices

15

9. After exiting the Telnet session, restore the TCP/IP address for the data system computer

network card (labeled Surveyor MS) to the original settings as follows (

):

a. Open the Internet Protocol Version 4 (TCP/IPv4) Properties dialog box (see

on

).

Figure 14.

Internet Protocol Version 4 (TCP/IPv4) Properties dialog box

b. In the IP Address box, type

172.16.0.101

.

c.

In the Subnet Mask box, type

255.255.0.0

.

d. Click

OK

.

e.

Exit the Control Panel.

After setting the stored IP address and subnet mask for the Agilent LAN interface, you are
ready to change the LAN interface initialization switches so that the LAN interface uses the
stored IP address. See

Setting the LAN Initialization Mode to “Using Stored”

.

«
...
25
26
27
28
29
...
»

Содержание Agilent 1200 Series



























































Отзывы:

Нет отзывов

Похожие инструкции для Agilent 1200 Series

Бренд: UFO Страницы: 16

Бренд: Dana Design Страницы: 20

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

Бренд: Teac Страницы: 76

Бренд: Teac Страницы: 3

Бренд: Teac Страницы: 50

Бренд: Teagle Страницы: 2

Бренд: VADDIO Страницы: 58

Бренд: Daavlin Страницы: 55

Бренд: Daavlin Страницы: 19

A/C Air Launcher 101050

Бренд: CITC Страницы: 10

Бренд: Meyer Страницы: 4

Бренд: Rottler Страницы: 96

Бренд: WIFO Страницы: 24

Бренд: Buyers Страницы: 2

Бренд: Drive Страницы: 2

Бренд: TECALEMIT Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды