Thermo Scientific Agilent 1200 Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 58

background image

Thermo Scientific

Agilent 1200 Series Getting Connected Guide for LC Devices

5

2

Setting Up the LAN Interface

This chapter describes how to configure the local area network (LAN) interface for the
Agilent 1200 Series LC system. For stable communication with the Xcalibur data system, one
of the modules in the Agilent LC system must contain either an on-board LAN interface or an
Agilent G1369 LAN card.

Determining the LAN Interface Type and Location

Agilent provides two options for the LAN interfaces:

• On-board LAN interface, which might be the standard configuration or you can order as

part of a module

• Agilent G1369 LAN card, which you can order separately

Note

For more information, refer to the user manual for the Agilent LAN card.

Contents

•

Determining the LAN Interface Type and Location

•

Setting the LAN Initialization Mode to “Using Default”

•

Setting the Stored TCP/IP Address for the LAN Interface

•

Setting the LAN Initialization Mode to “Using Stored”

IMPORTANT

Do not install more than one LAN card in the Agilent LC system. If one of

the modules in the LC stack includes an on-board LAN interface, do not install a LAN
card.

«
...
15
16
17
18
19
...
»

Содержание Agilent 1200 Series



























































Отзывы:

Нет отзывов

Похожие инструкции для Agilent 1200 Series

Бренд: 3M Страницы: 2

Бренд: dbx Страницы: 2

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

Бренд: RBC Bioscience Страницы: 24

Бренд: S&C Страницы: 16

Бренд: S&C Страницы: 23

ULTRATHERM 908i

Бренд: gbo Страницы: 32

Бренд: Dantel Страницы: 6

Бренд: Zero 88 Страницы: 22

Бренд: Yaasa Страницы: 20

Бренд: DAAB Страницы: 12

SimNewB Anomaly Set

Бренд: laerdal Страницы: 10

Бренд: Biosonic Страницы: 2

Бренд: Petzl Страницы: 7

RGB Studio Beam Driver

Бренд: SHOWTEC Страницы: 16

Бренд: Bondura Страницы: 10

Бренд: Beaumont Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды