Thermo King Rail Edition SLXi-DRC Скачать руководство пользователя страница 5

Страница: 5 / 104

TK 56433-5-MM-EN

Antifreeze Maintenance
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Checking the Antifreeze. . . . . . . . . . . . . . . 33
Changing the Antifreeze . . . . . . . . . . . . . . 33

Bleeding Air from the Cooling
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Engine Thermostat . . . . . . . . . . . . . . . . . . . 34
Coolant Level Switch . . . . . . . . . . . . . . . . . 34

Testing the Coolant Level Switch . . . . . . . 34
Checking the Float . . . . . . . . . . . . . . . . . . . 35
Replacing the Coolant Level
Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Engine Fuel System. . . . . . . . . . . . . . . . . . . . . . 35

High Speed . . . . . . . . . . . . . . . . . . . . . . . . . 39
Low Speed . . . . . . . . . . . . . . . . . . . . . . . . . 39

Injection Pump Timing . . . . . . . . . . . . . . . 40
Injection Pump Removal. . . . . . . . . . . . . . 43
Injection Pump Reinstallation . . . . . . . . . 44
Fuel Solenoid . . . . . . . . . . . . . . . . . . . . . . . . 44

Testing the Fuel Solenoid . . . . . . . . . . . . . 45
Fuel Solenoid Replacement . . . . . . . . . . . 46

Trochoid Feed Pump . . . . . . . . . . . . . . . . . 46

Trochoid Feed Pump Leaks . . . . . . . . . . . . 47
Trochoid Feed Pump
Replacement . . . . . . . . . . . . . . . . . . . . . . . 47

Cold Start Device . . . . . . . . . . . . . . . . . . . . 48

Checking Cold Start Device
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Cold Start Device Replacement . . . . . . . . 48

Engine Valve Clearance Adjustment. . . . . . . 49

Crankcase Breather . . . . . . . . . . . . . . . . . . . . . . 50

EMI 3000 Air Cleaner. . . . . . . . . . . . . . . . . . . . . 51

Belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Fan Drive Belt. . . . . . . . . . . . . . . . . . . . . . . . 52

Fan Drive Belt Replacement . . . . . . . . . . . 52
Fan Drive Belt Adjustment . . . . . . . . . . . . 54

Engine/Cross Shaft Belt. . . . . . . . . . . . . . . 55

Assembly of Tensioner Clutch . . . . . . . . . 56
Engine/Cross Shaft Belt
Replacement . . . . . . . . . . . . . . . . . . . . . . . 56

Water Pump Belt . . . . . . . . . . . . . . . . . . . . . 58

e .. .. .. .. .. .. .. .. .. .. .. .. .. .. 5

Refrigerant Charge . . . . . . . . . . . . . . . . . . . . . . 59

Testing The Refrigerant Charge With
An Empty Trailer . . . . . . . . . . . . . . . . . . . . . 59
Testing the Refrigerant Charge with
a Loaded Trailer . . . . . . . . . . . . . . . . . . . . . 59
Testing for an Overcharge . . . . . . . . . . . . 59

Moisture Indicating Sight Glass . . . . . . . . . . . 60

Refrigerant Leaks . . . . . . . . . . . . . . . . . . . . . . . . 60

Checking Compressor Oil . . . . . . . . . . . . . . . . 60

High Pressure Cutout Switch
(HPCO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Three-Way Valve Condenser Pressure
Bypass Check Valve. . . . . . . . . . . . . . . . . . . . . . 61

Electronic Throttling Valve (ETV) . . . . . . . . . . 62

Pressure Transducers . . . . . . . . . . . . . . . . . . . . 63

Hot Gas Bypass Valve . . . . . . . . . . . . . . . . . . . . 63

nss .. .. .. .. .. .. .. 6

Refrigeration System Components . . . . . . . . 64

Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Compressor Coupling Removal
(Standard Units) . . . . . . . . . . . . . . . . . . . . . 65
Compressor Coupling Installation
(Standard Units) . . . . . . . . . . . . . . . . . . . . . 66

Compressors with Pressurized Seal
Cavity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Hex Drive Compressor Seal
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Condenser Coil . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Discharge Vibrasorber . . . . . . . . . . . . . . . . . . . 70

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 70

In-Line Condenser Check Valve . . . . . . . . . . . 71

blle

e o

off C

ntte

nttss

Содержание Rail Edition SLXi-DRC









































































































Результаты поиска

Содержание Rail Edition SLXi-DRC

Отзывы:

Похожие инструкции для Rail Edition SLXi-DRC

Бренды по названию

Популярные бренды

Thermo King Rail Edition SLXi-DRC, Руководство по обслуживанию

Результаты поиска

Содержание Rail Edition SLXi-DRC

Отзывы:

Похожие инструкции для Rail Edition SLXi-DRC

Бренды по названию

Популярные бренды