background image

TK 56433-5-MM-EN

47

Trochoid Feed Pump Outlet Pressure

Cranking

15-30 psi (103-206 kPa)

Low Speed

30-50 psi (206-345 kPa)

High Speed

65-87 psi (450-600 kPa)

Figure 41.

Trochoid Feed Pump Location

1.

Trochoid Feed Pump Outlet Pressure Port

2.

Trochoid Feed Pump

Trochoid Feed Pump Leaks

Internal – If the seal in the trochoid feed pump fails, it
could allow some fuel to leak into the engine oil. A
faulty injection nozzle can also dilute the engine oil
with fuel. Replace the trochoid feed pump if the engine
oil is being diluted with fuel and a faulty injection
nozzle or fuel transfer pump is not the cause.

External – Replace the O-ring seal between the trochoid
feed pump and the injection pump if oil is leaking.
Torque the bolts to prevent leaks (6 to 7 ft-lb [8 to 10
N•m]).

Replace all O-rings if fuel is leaking. Torque the Allen
head screws and Hex head bolts to prevent leaks (6 to 7
ft-lb [8 to 10 N•m]).

Trochoid Feed Pump Replacement

Use the following procedure to replace the trochoid
feed pump.

1. Remove the four hex head screws that attach the

trochoid feed pump to the injection pump (see

Figure 42, p. 47

). Do not remove the two Allen head

screws.

Figure 42. Trochoid Feed Pump Removal

1.

Allen Head Screws (Do Not Remove)

2.

Hex Head Screws

2. Remove the trochoid feed pump from the injection

pump.

N

No

otte

e:: The gear on the trochoid feed pump is

lubricated with engine oil. Some engine oil
might leak out of the injection pump when
the trochoid feed pump is removed. The
trochoid feed pump does not need to be
timed when it is installed.

3. Clean the area on the injection pump from which

the trochoid feed pump was removed.

4. Place new O-rings on the new trochoid feed pump

and make sure it is clean.

Figure 43.

Trochoid Feed Pump

1.

O-Rings

5. Place the new trochoid feed pump on the injection

pump.

E

En

ng

giin

ne

e M

Ma

aiin

ntte

en

na

an

ncce

e

Содержание Rail Edition SLXi-DRC









































































































Отзывы: