Thermo King Rail Edition SLXi-DRC Скачать руководство пользователя страница 52

Страница: 52 / 104

TK 56433-5-MM-EN

Fan Drive Belt

Figure 54.

Belt Arrangement

Fan Shaft

10.

Fan Drive Belt Tensioner

Upper Condenser Blower

11.

Idler Pulley

Condenser Inlet Orifice

12.

Sliding Idler Pulley

Alternator

13.

Cross Shaft/Fan Pulley

Fan Drive Belt

14.

Idler Pulley

Alternator Pulley

15.

Engine/Cross Shaft Belt Tensioner Clutch

Lower Condenser Blower

16.

Compressor/Clutch Belt

Cross Shaft/Engine Pulley

17.

Compressor Coupling

Cross Shaft (Jackshaft)

Fan Drive Belt Replacement

1. Place a 17 mm socket wrench over the head of the

fan drive belt tensioner bolt in a horizontal starting
position. Slowly pull down on the tensioner until
the belt is loose enough to remove from the

tensioner. Do not pull the tensioner down farther
than needed to remove the belt.

Содержание Rail Edition SLXi-DRC









































































































Результаты поиска

Содержание Rail Edition SLXi-DRC

Отзывы:

Похожие инструкции для Rail Edition SLXi-DRC

Бренды по названию

Популярные бренды

Thermo King Rail Edition SLXi-DRC, Руководство по обслуживанию

Результаты поиска

Содержание Rail Edition SLXi-DRC

Отзывы:

Похожие инструкции для Rail Edition SLXi-DRC

Бренды по названию

Популярные бренды