Thermia Atria Optimum Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 76

background image

If it is a floor heating installation (default = radiator) change the following:

1. Press the left button for five seconds to open the SERVICE menu.
2. In the SERVICE -> INSTALLATION -> FACTORY SET menu. Select parameters FLOOR.

If necessary; change the number of auxiliary heating steps.

1. In the SERVICE -> AUX. HEATER -> MAX STEP menu. Chose the number of auxiliary heating steps with + or -.

10.2.2

Select system solution

Further information about system solution can be found in the following chapters:

▪

Piping installation

▪

Selection of system solution and connection of external aux. heater

System solution 1

At delivery the heat pump is configured for system solution 1.

System solution 2

1. Select SERVICE -> AUX HEATER -> EXT.AUX.HEATER menu.
2. Set parameter EXT.AUX HEATER to ON.
3. Set parameter REV.V. HOT WATER to INT.

System solution 3

1. Select SERVICE -> AUX HEATER -> EXT.AUX.HEATER menu.
2. Set parameter EXT.AUX HEATER to ON.
3. Set parameter REV.V. HOT WATER to EXT.

10.2.3

Other settings

If necessary; configure settings for the following (see also SERVICE menu and the actual

Installation manual

):

▪

COOLING

▪

POOL

▪

SHUNT GROUP

▪

BUFFER TANK

10.3

Filling and bleeding the water heater and heating system

1. Turn off heating system circulation pump and external circulation pump.
2. Fill the water heater with cold water by opening the shut-off valve (80) on the incoming cold water pipe.
3. Bleed by opening one of the hot water taps.
4. Then fill the water heater coil and the heating system with water through the shut-off valve (80) to the return line to a pressure of

approximately 1 bar.

5. Open all heating system valves fully.
6. Bleed all heating systems and the water heater coil.
7. Refill the heating system to a pressure of approximately 1 bar.
8. Repeat the procedure until all air has been removed.
9. Check the system for leakage.

10. Leave the radiator valves fully open.

Installation Guide

Domestic heat pumps

VMGFP202

Thermia Värmepumpar

60

«
...
58
59
60
61
62
...
»

Содержание Atria Optimum













































































Отзывы:

Нет отзывов

Похожие инструкции для Atria Optimum

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 86

Бренд: Danfoss Страницы: 28

Бренд: Jandy Страницы: 108

Бренд: Jandy Pro Series Страницы: 40

Бренд: L.B. White Страницы: 18

Бренд: VEAB Страницы: 6

Бренд: Gasmate Страницы: 20

Бренд: Underhill Страницы: 2

Бренд: Masterflex Страницы: 67

Бренд: HearthRite Страницы: 24

Бренд: Sure Flame Страницы: 32

Бренд: Kamoer Страницы: 2

Бренд: Pakole Страницы: 30

Бренд: Pattfield Ergo Tools Страницы: 162

Бренд: Fenix Страницы: 12

Бренд: Saab Страницы: 40

SUBMERSIBLE DIRTY WATER PUMP 93819

Бренд: Pacific hydrostar Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды