Thermia Atria Optimum Скачать руководство пользователя страница 47

Страница: 47 / 76

INFORMATION menu

Open the menu by pressing the left or right button. The menu also shows history and operating times.

The menu information below describes all possible parameters. The parameters that appear in the display

vary depending on the selections made in menus (e.g. type of heat pump) and on the connected hardware

(e.g. expansion card and defrost card).

▪

INFORMATION

▪

OPERAT.

▪

HEAT CURVE

▪

HEAT CURVE 2 (if shunt group is activated)

▪

TEMPERATURE

▪

OPERAT. TIME

▪

DEFROST

▪

LANGUAGE

8.1

Sub-menu OPERAT.

Menu selection

Meaning

Factory setting

(OFF)

The installation is fully switched off. This mode is also used to acknowledge certain

alarms.

CANCEL = starting point, no changes made.

To select OFF as operating mode, press the minus sign once to scroll down one step and

press the right arrow once.

AUTO

Automatic operation with both heat pump and auxiliary heater permitted. If the number

of power stages for auxiliary heating are set to zero (SERVICE -> AUX. HEATER -> MAX

STEP) only AUTO or OFF can be selected as operating mode.

HEAT PUMP

Operation with only compressor permitted.

No peak heating charging (anti-legionella function) with only

heat pump operation.

AUX. HEATER

Operation with only auxiliary heater permitted.

HOT WATER

Operation with heat pump for hot water production and auxiliary heater during peak

heating charging (anti-legionella function).

MANUAL TEST

Only displayed when the value for MANUAL TEST is set to 2 in the SERVICE menu. Out-

puts that control components are activated manually.

8.2

Sub-menu HEAT CURVE

Menu selection

Meaning

Factory setting

CURVE

Calculated supply temperature at 0°C outdoor temperature. Shown as a graphic curve.

The curve will be limited by the set values of MIN and MAX.

40°C(for under

floor heating

30°C)(range:

22°C / 56°C)

MIN

Minimum permitted supply temperature, if the temperature for heat stop has been

reached and the heat pump has stopped.

10°C(range:

10°C / 50°C)

MAX

Maximum calculated setpoint value of the supply temperature.

55°C(for under

floor heating

45°C)(range:

40°C / 85°C)

CURVE +5

Local increase or reduction of CURVE at an outdoor temperature of +5°C. Shown in the

graph for CURVE.

0°C(range: -5°C /

5°C)

Installation Guide

Domestic heat pumps

Thermia Värmepumpar

VMGFP202

Содержание Atria Optimum













































































Результаты поиска

Содержание Atria Optimum

Отзывы:

Похожие инструкции для Atria Optimum

Бренды по названию

Популярные бренды

Thermia Atria Optimum, Руководство по установке

Результаты поиска

Содержание Atria Optimum

Отзывы:

Похожие инструкции для Atria Optimum

Бренды по названию

Популярные бренды