Thermal Dynamics CUTMASTER 39 Скачать руководство пользователя

Страница: 60 / 80

cutmaster 39

SERVICE

5-16

Manual 0-4976

14. Reinstall the Power Supply cover. Con-

nect the gas input line to the inlet port.

Connect the Power Supply to primary input

power.

15. Test the Power Supply for proper opera-

tion.

C. Optional Single-Stage Filter Element

Replacement

NOTE

The  Power  Supply  shuts  down  automatically
when the Filter Element becomes completely satu-
rated.  The Filter Element can be removed from
its housing, dried, and reused.  Allow 24 hours
for Element to dry.

1. Remove power from power supply.

2. Disconnect gas supply hose.

Art # A-02476

Filter

Element

(Cat. No. 9-7741)

Housing

Cover

Barbed

Fitting

Spring

Assembled Filter

O-ring

(Cat. No. 9-7743)

3. Turn the Cover counter-clockwise and re-

move it from the Filter Housing. The Filter

Element is located inside the Housing.

4. Remove the Filter Element from the Hous-

ing and set Element aside to dry.

5. Wipe inside of housing clean, then insert

the replacement Filter Element open side

first, as shown.

6. Replace Housing on Cover.

7. Attach gas supply hose.

NOTE

If unit leaks between housing and cover, inspect
the O-Ring for cuts or other damage.

5.13 Right Side Internal Parts

Replacement

Refer to Section 6 for Right Side Internal

Parts List and overall detailed drawing.

WARNING

Disconnect input power at the source and
bleed down the system before attempting
these procedures.

A. Standard Filter Element Replacement

1. Remove the cover per Subsection 5.07-B.

2. Remove power from the power supply;

turn off the gas supply.

Art # A-07936

Replacement

Element

No. 9-0182

Ring

Spool

Bowl

3. Unscrew the bowl on the bottom of the

Regulator/Filter Assembly. The filter ele

ment will be visible and still attached to the

main body of the Regulator/Filter Assem-

bly.

4. Grasp the filter element and unscrew it

from the Regulator/Filter body. The filter

element will come off with a spool and

some additional pieces.

5. Note the correct assembly of the filter/

spool then remove the filter from the

spool. Either clean or replace the filter ele

ment.

6. The filter element and spool, with the

baffle ring in place (teeth facing down

ward) can be screwed back into the Regu-

lator body by compressing the spring on

the spool. Tighten firmly by hand.

7. Reinstall the bowl. Connect the drain tube

to the bowl.

8. Reinstall Power Supply cover .

9. Turn on the air supply. Test the Power

Supply for proper operation.

Содержание CUTMASTER 39

















































































Результаты поиска

Содержание CUTMASTER 39

Отзывы:

Похожие инструкции для CUTMASTER 39

Бренды по названию

Популярные бренды

Thermal Dynamics CUTMASTER 39, Руководство по обслуживанию

Результаты поиска

Содержание CUTMASTER 39

Отзывы:

Похожие инструкции для CUTMASTER 39

Бренды по названию

Популярные бренды