![background image](http://html1.mh-extra.com/html/thermal-dynamics/auto-cut-300-xt/auto-cut-300-xt_operating-manual_1103284049.webp)
AUTO-CUT 300 XT
Manual 0-5300
INSTALLATION
3-23
Control Cable.
The iHC board can be supplied with a wire harness and connector (shown in previous image), to be installed in
the rear panel hole labeled “Height Control” . The connector mates with a cable from the iHC. For other height
control V-D boards a strain relief can be installed in this hole for those cables. Refer to Appendix for wiring diagram.
USER INPUT
HEIGHT CONTROL
F1 - 8A SB 230 VAC
F2 - 8A SB 230 VAC
CB4 - 5A 120 VAC
CB3 - 5A 24 VAC
CB2 - 5A 120 VAC
J55 - GCM
J15 - CNC
J59 - RAS
J70 - HE
J54 - TSC /COMM
Ohmic clip cable port
V-D Board connection
Art # A-12080
Arc Voltage Connections.
The XT plasma supplies provide a terminal strip, TB4, on the right side ahead of the CCM module for connections
to Arc V- (Torch); Tip V (Pilot); Arc V + (Work). If the V-D board requires separate power, 24 VAC and 120 VAC is
available on the terminal strip TB4. Refer to the wiring diagram in the Appendix for more information.
24 VAC
@ 1A
TB4
1
2
3
4
5
6
7
120 VAC
@ 100 ma.
Work
Tip Volts
(Pilot)
Arc Volts
(Torch)
Art # A-11954
“Ohmic” or Shield (cup) cable.
Some height controls including the iHC find the plate using an electrical or resistance measurement, thus “ohmic”,
contact between the conductive end of the torch and the metal or “plate” being cut. A wire, usually a single highly
flexible wire that withstands the reflective heat from the arc, is connected between the V-D board and the torch shield
cup. The XT torch includes a metal spring clip which slips into a groove in the shield cup allowing easy removal for
parts change. The Ohmic wire can be connected to this clip with a ¼” female push-on terminal.
Significant amounts of high frequency (HF) energy causing electromagnetic interference (EMI) can be conducted
along this wire due to it’s close coupling to the torch. This is the reason for mounting the V-D board away from
the CCM and close to the rear panel where the Ohmic wire does not need to pass near other sensitive electronics.
It is especially recommended that the Ohmic wire not be routed near the CCM module or along the torch leads.
Refer to Appendix for wiring diagram.
Ferrite cores.
It is recommended that the Ohmic Sensing wire be wrapped through a ferrite core with several turns, at least 3 but
more is better, to reduce the energy conducted to the V-D board and into the plasma supply. The ferrite core should
be located on the wire where it enters the plasma supply. A second ferrite core added several feet (couple of meters)
from the torch will further reduce the conducted EMI that may couple to other cable/wires and cause interference.
Refer to Appendix for wiring diagram.
Содержание AUTO-CUT 300 XT
