Thecus N2520 series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 130

background image

41

Chapter 3: System Administration

D2 Stack Target ACL

If the stack target Public setting set to Yes, then the ACL button will be grayed out. However, if Public
setting is set to No, then the ACL button will be available for you to setup user access permissions for
the stack target.
The ACL settings will be exactly the same as the system folder that you may have setup previously.

E2 Reconnect a Stack Target

This is used to enable stack target devices that may have been disconnected due to a power outage
or a disconnected network. When this happens, the Reconnect button will become available. To at-

a disconnected network. When this happens, the Reconnect button will become available. To at-

. When this happens, the Reconnect button will become available. To at-

When this happens, the Reconnect button will become available. To at-

, the Reconnect button will become available. To at-

button will become available. To at-

will become available. To at-

become available. To at-

available. To at-

To at-

tempt to reconnect the stack target, click Reconnect.

«
...
45
46
47
48
49
...
»

Содержание N2520 series



































































































































Отзывы:

Нет отзывов

Похожие инструкции для N2520 series

ALTOS R910 Series

Бренд: Acer Страницы: 74

Univerge SV9100

Бренд: NEC Страницы: 78

UNIVERGE SL2100

Бренд: NEC Страницы: 34

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 975

Бренд: IBM Страницы: 214

TrueNAS R Series

Бренд: iXsystems Страницы: 24

Бренд: Transcend Страницы: 24

Бренд: NTI Страницы: 35

Бренд: Hologic Страницы: 30

Rotate FlashPen

Бренд: Hama Страницы: 4

Бренд: Velvac Страницы: 55

Бренд: ICP DAS USA Страницы: 4

Бренд: ADTRAN Страницы: 4

Бренд: Supermicro Страницы: 62

Бренд: 3Com Страницы: 63

IE-SW-AL18M-16TX-2GC

Бренд: Weidmüller Страницы: 2

Бренд: IBM Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды