Theben 2080045, Руководство пользователя

Страница: 7 / 14

7
Room correction factor = Brightness value at the ceiling
Brightness value on the work
surface
We recommend the following procedure:

Dim all lights as far as possible. If possible, close blinds.

The lux meter is placed on the work surface below the
sensor and the measured lux value is entered via the
“SendoPro, theSenda B/App” management remote
control, <brightness measurement value Win, Mid, Inn,
Int> parameter is entered and sent to the detector. During
lux measurements, observe the distances shown in the
diagram. Carry out all measurements at table height.
•
<Brightness measurement value Win>: Lux measurement
towards the window
•
<Brightness measurement value Mid>: Lux measurement
in the middle (below detector)
•
<Brightness measurement value Inn>: Lux measurement
towards the interior
•
<Brightness measurement value Int>: Average of all 3 lux
measurements Win + Mid + Inn.

The room correction factor is calculated from this
automatically. Values between 0.05 and 2.0 are permitted.
Calculated or entered values outside the permitted range
will automatically be set to the appropriate limit value.

The calculated room correction factor will be applied
immediately. For monitoring purposes, the room correction
factor can be queried via the <room corr. factor Win, Mid,
Inn, Int> parameter.
L
The standard value is 0.3 and is suitable for most appli -
cations. Changes are only sensible in strongly deviating
situations.
Detection sensitivity
The detector has 5 sensitivity increments. The basic setting is
the middle increment (3).
Increments 1 to 5 can be selected and sent to the detector
with the “SendoPro, theSenda B/App” management remote
control. On the “theSenda P” installation remote control, the
sensitivity can be decreased by one increment each time the
button
is pushed or increased with the button.
Value range
Incre-
ment
Sensitivity
1 Very insensitive
2 Insensitive
3 Standard
4 Sensitive
5 Very sensitive
By selecting the test presence operating mode, the set sensi-
tivity increment is not changed.
Lighting time delay
The time delay applies jointly to all lighting channels.
Value range
Adjustable values with “SendoPro 868-A” manage -
ment remote control
10 s – 60 min
In the “theSenda P” installation remote control, the
following values are available
10 s (button ),
30 s, 60 s, 2 min,
10 min, 20 min,
60 min (button
)
Short presence
If someone goes into an unoccupied room only briefly and
leaves it within 30 seconds, then the lighting will be switched
off prematurely after 2 minutes (short-term presence). The
short-term presence can be used for the fully automatic and
semi-automatic configuration types.
Value range (with SendoPro, theSenda B/App)
The time delay is applied according to the set time delay. Off
Short-term presence is active. On
Energy saving mode eco/eco plus
The selection of “eco” stands for optimum switching behavi-
our, while “eco plus” stands for maximum energy saving.
Value range (with SendoPro, theSenda B/App)
“eco” The time delay adjusts to the user behaviour by self-learning.
It does not drop below the set value.
“eco plus” The set time delay remains unchanged (no self-learning
effect). Faster response to brightness detection than with
“eco”.
Presence switch-on delay
The contact of the external DALI relay closes when some -
one is present regardless of the brightness and after the set
switch-on delay has elapsed. Buttons and the configuration
type (fully automatic device/semi-automatic device) do not
affect the relay contact.
Value range (with SendoPro, theSenda B/app)
No switch-on delay 0 s
Switch-on delay 10 s – 30 min
Presence time delay
The relay contact of the external DALI relay only opens once
the set time delay has elapsed in periods of absence.
Value range
Adjustable values from Sendo-
Pro/theSenda B/app
10 s – 120 min
Adjustable values from theSenda
P
10 s, 30 s, 60 s, 2 min, 10 min, 20 min,
120 min
Switch-on dimming value C1, C2, C3
The lighting is switched on with the switch-on dimming value
in both the switching operation and constant light control.