background image

2

Constant light control

Constant light control compensates for variations in daylight 

by controlling the lighting.

 The overall brightness will be kept 

constant at the desired brightness level. The lighting is swit

-

ched on with the switch-on dimming value and controlled so 

that it reaches the set brightness setpoint value. Depending 

on „school“ or „office“ configuration type, the presence detec

-

tor behaves differently after manual dimming via button:

 

„School“ configuration type for applications in classrooms 

and meeting rooms:

 

y

Manual dimming deactivates constant light control.

 

y

Lighting remains at dimmed level when room is occupied 

(no brightness influence).

 

y

Switching off and on returns to standard operation.

 

„Office“ configuration type for applications in small and 
large offices:

 

y

Constant light control remains active temporarily after 

manual dimming to the current brightness value as the new 

brightness setpoint value.

 

y

The new brightness setpoint value only applies if the room 

is occupied.

 

y

After the lighting time delay expires, the originally set 

brightness setpoint value is restored.

Switching operation

Switching response is controlled by presence and brightness. 

The channel light switches on in darkness and if presence 

is detected. The light switches off when there is sufficient 

brightness or once the room is vacated after the set lighting 

time delay. The light is switched on with the switch-on dim

-

ming value. By using the button, the intensity of artificial light 

can be changed for the duration of the presence. Following 

override using the button, the light stays on for at least 30 

min. The light is forced off after a preset time delay if the 

room was (previously) vacated.

Standby (orientation light)

The standby function acts as an orientation light. After the 

lighting time delay expires, the lighting is set to the standby 

dimming value (1 – 25 %) of the lamp output. The standby 

time can be set to between 0 s and 60 min or permanently. 

The lighting is switched off if the brightness level in the room 

exceeds the brightness setpoint value. The lighting automati

-

cally returns to the standby brightness if the room brightness 

falls below the brightness setpoint value. When the room 

is entered again, the detector returns to the programmed 

brightness setpoint value, either automatically (fully automa-

tic device) or after the button is operated (semi-automatic 

device).

Lighting time delay

The minimum time delay (10 s – 60 min) is adjustable. It 

adjusts automatically to the user‘s behaviour and can incre-

ase to 30 minutes or drop back to the set minimum time. 

With settings ≤ 2 min or ≥ 30 min, the time delay remains 

unchanged at the set value. If someone goes into an unoccu

-

pied room only briefly and leaves it within 30 seconds, then 

the lighting will be switched off prematurely after 2 minutes 

(short-term presence).

Push button control

The lighting can be manually switched or dimmed at any time 

at the push of a button. A short press of the button switches 

the light on or off, a longer press of the button dims the ligh-

ting up or down. The dimming direction changes each time 

the button is pressed. If the lighting is switched off manually, 

the lighting will stay off as long as the room is occupied. The 

lighting switches on again automatically after the time delay 

has expired. Please pay attention to the differing behaviour of 

the constant light control and the switching operation, which 

is described in the corresponding chapter.

Fully or semi-automatic device

Lighting control via the presence detector operates fully 

automatically for increased comfort or semi-automatically for 

greater energy savings. The lighting switches on and off auto

-

matically as a “fully automatic device”. As a “semi-automatic 

device”, the lighting must always be switched on manually. 

The lighting is switched off automatically.

Exceptionally easy configuration of the energy-saving beha-

viour

By using the selection “eco” for optimal switching behaviour 

or “eco plus” for maximum energy savings, users can adjust 

the presence detector to their needs.

5.  Detection area

The circular detection area of theRonda P presence detector 

covers a large detection area, and permits a complete room 

coverage with many applications. Note that seated and wal

-

king persons are detected in different areas. The recommen

-

ded installation height is 2 m – 6 m. As installation height 

increases, the sensitivity of the presence detector decreases. 

Walking motions are necessary from installation heights of 

3.5 m, and the detection areas of several detectors should 

overlap in the marginal zones. The detection range is reduced 

as the temperature increases.

Seated persons:

The presence detector reacts very sensitively to the slightest 

movements. The information refers to table height (approx. 

0.80 m).

S

t

 r

 s

12

4

3

3

4

12

Содержание 2080045















Отзывы: