Thane Fitness Orbitrek X2, Руководство пользователя

Страница: 9 / 12

Owner’s Manual
16
pArT NO. pArT NAMe speC MATerIAL QUANTITY
1
LEFT HINGE BOLT 1/2" 40Cr 1
2 BUSHING II
φ
28.6*2 PA6+MoS2 6
3 LOCK NUT M10 Q235 2
4 FRONT STABILIZER BUSHING PE 2
5 LEFT SLIDER PIN 1
6 SPRING WASHER 1/2" 65Mn 2
7 LEFT LOCK NUT 1/2" 1
8 ADJUSTABLE END CAP 50*1.5 PAK < 200ppm PE 2
9 CARRIAGE BOLT M8*60 Q235 2
10 REAR STABILIZER
φ
50.8*1.5*580 Q195 1
11 ARC WASHER
φ
8 Q235 2
12 DOMED NUT M8 Q235 2
13 PIN
φ
5 Q235 2
14 FLAT WASHER φ 8 Q235 4
15 HEX HEAD BOLT M10*55 Q235 2
16 SCREW ST4.2*19 35 2
17 BEARING SPRING WASHER-B
φ
20 35 2
18 BUSHING I φ 18* φ 14* φ 10*10;4g PA6+MoS2 4
19 LEFT PEDAL TUBE 1
20 PEDAL SCREW M8*20 Q235 4
21 BEARING 6004ZZM 2
22 RIGHT HANDLEBAR
φ
25.4*3*945 Q195 1
23 FRONT STABILIZER 1
24 LEFT CONNECTING TUBE 1
25 FRONT END CAP PAK < 200ppm PE 2
26 RIGHT PEDAL PAK < 10ppm pp 1
27 LEFT PEDAL PAK < 10ppm pp 1
28 HEX HEAD BOLT M6*45 Q235 2
29 WHEEL φ 23* φ 7*31,PAK<200ppm PA 2
30 LOCK NUT M6 Q235 3
31 HINGE SCREW 3/8"*20 Q235 2
32 SPRING WASHER 3/8" 65Mn 2
33 D SHAPE WASHER
φ
28 Q235 2
34 LOCKING KNOB M8*45,PAK < 10ppm PP+Q235 2
35 PLASTIC SLEEVE PE 4
36 MAIN FRAME Q235 1
37 COMPUTER TZ-2172 1
38 SPINDLE BAR φ 15.8*423.5 45# 1
39 FOAM GRIP
φ
23*
φ
33*275<PAK<10ppm NBR 2
40 LEFT HANDLEBAR
φ
25.4*3*945 Q195 1
41 HANDLEBAR END CAP PP 2
42 RIGHT HINGE BOLT 1/2" 40Cr 1
43 HEX SOCKET BOLT M8*55 35 2
44 BEARING SPRING WASHER
φ
17 65Mn 2
45 END CAP PP 2
46 END CAP PE 2
47 RIGHT SLIDER PIN 1
48 SPRING 1
φ
8 65Mn 2
49 SLIDING BLOCK PA+65Mn 2
50 SENSOR BRACKET ABS 1
51 SCREW M5*15 Q235 4
52 SPRING PIN 2
Insert the Spindle Bar (No.38)
through the Left Connecting Tube
(No.24) into the Main Frame, and
then into Right Connecting Tube
(No.55). Put a D Shaped Washer
(No.33) and a Spring Washer (No.32)
on either side of the Spindle Bar.
Make sure the D Shaped Washer is
mounted on and aligned with the
D shaped end of the Spindle Bar,
as illustrated in Fig. 3a.
Insert Hinge Screws (No.31) on
both ends of the Spindle Bar and
tighten both screws using two Allen
Wrenches.
Step 3: Attaching Spindle Bar
31
24
36
38
31
33
32
33 32
55
Fig. 3
Fig. 3a
38
33
Owner’s Manual
9