TGW NBS 90 PolySort Скачать руководство пользователя страница 57

Страница: 57 / 83

NBS®90 PolySort & SP IOM

P/N: 1193974

Revision Date: 4/25/2019

Page

9.4: NBS90

OLY

ORT

INE

ONNECTIONS

Source Air Connection

Select the best position along the conveyor to connect the source air from a drop line. Ideally, the

regulator should be centrally located along the sorter and should not be more than 80' from the furthest

diverter/transfer or drive.
Attach the filter/regulator assembly to the bottom flange of the side frame using the mounting bracket

supplied with the kit.
The source airline that distributes air to the diverters/transfers should be 1/2" hose that is rated to

handle a pulsating 60psi line pressure. TGW Systems part number 89000572 TUBING, URETHANE

1/2 OD is available for this purpose.
Cut into the supply line along the sorter bed and install the source airline tee fitting TGW Systems part

number 89000640. Connect the source air line between this fitting and the filter/regulator output.
The hose size at each diverter/transfer is 3/8 OD and the source airline can be tapped at each location

using TGW Systems part number 89000640 1/2” tee and 1/2” x 3/8” tube reducer fitting TGW Systems

part number 1155149.

Low Pressure Air Switch

The installation of an air pressure switch in the NBS air supply circuit, to detect a drop in air pressure

below required levels, is recommended. If pressure drops below approximately 40 PSI, the conveyor

system should shut off.
It is recommended that this air switch be located either at the furthest end of the source air line away

from the regulator or at the pneumatic belt take-up located in or near the drive bed at the discharge end

of the sorter.

•

Do not use a lubricator. When replacing filter/regulator bowl, lightly lubricate seal with

mineral oil. Do not use synthetic oils such as esters or silicones. DO NOT get oil inside

filter/regulator bowl.

•

The function of the low pressure air switch is to protect the drive pulley and the NBS

narrow belts from being damaged from slipping under load in the event of an air

pressure disruption. Loss of air pressure may also cause diverter / transfer jams.

CAUTION

Содержание NBS 90 PolySort




















































































Результаты поиска

Содержание NBS 90 PolySort

Отзывы:

Похожие инструкции для NBS 90 PolySort

Бренды по названию

Популярные бренды

TGW NBS 90 PolySort, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание NBS 90 PolySort

Отзывы:

Похожие инструкции для NBS 90 PolySort

Бренды по названию

Популярные бренды