manualshive.com logo in svg

TFS NTP80plus, Справочное руководство


Поделиться
Скачать
background image

 

 

MANUAL P/N 900000165 REV H 

25 

For network-wide broadcast the address would be 255.255.255.255, for a subnet set the host 
part of the address to the last host address, so for network 192.168.101.0 that would be 
192.168.101.255 
 
The above parameters are applied when submit is pressed. This will stop and re-start the NTP 
service. 
 

Local Time Zone 

The local time zone allows the front status page and the front panel display to show local time 
rather than UTC. Note that all NTP operations are performed with UTC. Setting this parameter 
has no effect on NTP operation. The factory configured GPRMC serial output options of the 
NTP80 provide a local-time message, that local time is also defined by this parameter. 
 
Press submit to change this value. 
The NTP80 is now configured. 
 

5.4

 

Status 

The status page shows the current running state of the NTP80. The top section shows the 
system state including how long it has been running and the currently loaded date and time. 
 

 
The GNSS status shows position and the satellite status. The top status will reflect the condition 
determined from the status number. This status is recorded in the event log. See 

Events

 for 

details. 

Содержание NTP80plus


























































Отзывы:

Нет отзывов

Похожие инструкции для NTP80plus

Canon ColorPASS-Z5000 Getting Started preview
ColorPASS-Z5000
Бренд: Canon Страницы: 130
AIC CB201-Z1 User Manual preview
CB201-Z1
Бренд: AIC Страницы: 52
B.E.G. LUXOMAT net ViSTATION Quick Start Manual preview
LUXOMAT net ViSTATION
Бренд: B.E.G. Страницы: 4
IBM Netfinity 1000-8477 21Y Hardware Maintenance Manual preview
Netfinity 1000-8477 21Y
Бренд: IBM Страницы: 268
IBM System x3500 M2 Type 7839 Installation And User Manual preview
System x3500 M2 Type 7839
Бренд: IBM Страницы: 126
Obvius AcquiLite EMB A7810 Installation And Operation Manual preview
AcquiLite EMB A7810
Бренд: Obvius Страницы: 29
SpectraLink NetLink SVP100 Installation, Configuration And Administration preview
NetLink SVP100
Бренд: SpectraLink Страницы: 31
7th Sense DeltaServer User Manual preview
DeltaServer
Бренд: 7th Sense Страницы: 60
Lenovo 7Y45 Setup Manual preview
7Y45
Бренд: Lenovo Страницы: 116
Lenovo 70F0 User Manual And Hardware Maintenance Manual preview
70F0
Бренд: Lenovo Страницы: 96
Lenovo 8753 Product Manual preview
8753
Бренд: Lenovo Страницы: 46
Lenovo 7Y54 Maintenance Manual preview
7Y54
Бренд: Lenovo Страницы: 138
Lenovo 8871 Product Manual preview
8871
Бренд: Lenovo Страницы: 56
Lenovo 8869 Product Manual preview
8869
Бренд: Lenovo Страницы: 64
Lenovo DU User Manual preview
DU
Бренд: Lenovo Страницы: 226
Lenovo BladeCenter HS22 Installation And User Manual preview
BladeCenter HS22
Бренд: Lenovo Страницы: 96
Lenovo BladeCenter HS23 Installation And User Manual preview
BladeCenter HS23
Бренд: Lenovo Страницы: 104
Lenovo 643815U Installation Manual preview
643815U
Бренд: Lenovo Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды