TFS NTP80plus Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 57

TFS NTP80plus Скачать руководство пользователя страница 50

MANUAL P/N 900000165 REV H

50

  codenumber OBJECT-TYPE
  SYNTAX OCTET STRING (SIZE(0..14))
  ACCESS read-only
  STATUS mandatory
   DESCRIPTION "Firmware part number"
  ::= {common 4}

  codeversion OBJECT-TYPE
  SYNTAX OCTET STRING (SIZE(0..8))
  ACCESS read-only
  STATUS mandatory
  DESCRIPTION "Firmware version number"
  ::= {common 5}

  systemstatus OBJECT IDENTIFIER ::= {tfs 4}

  lastevent OBJECT-TYPE
  SYNTAX INTEGER
  ACCESS read-only
  STATUS mandatory
  DESCRIPTION "Last event ID"
  ::= {systemstatus 2}

  syslogTable OBJECT-TYPE
  SYNTAX SEQUENCE OF SyslogEntry
  ACCESS not-accessible
  STATUS mandatory
  DESCRIPTION "System log table"
  ::= {systemstatus 1}

  syslogEntry OBJECT-TYPE
  SYNTAX SyslogEntry
  ACCESS not-accessible
  STATUS mandatory
  DESCRIPTION "System log record"
  INDEX {eventid}
  ::= {syslogTable 1}

  SyslogEntry ::= SEQUENCE { timestamp INTEGER,
  resolver INTEGER,
  eventid INTEGER,
  severity INTEGER,

module OCTET STRING,

function OCTET STRING,

  description OCTET STRING
  }

  timestamp OBJECT-TYPE
  SYNTAX INTEGER
  ACCESS read-only
  STATUS mandatory
  DESCRIPTION "time as number of secs since 1 January 1970"
  ::={syslogEntry 1}

  resolver OBJECT-TYPE
  SYNTAX INTEGER
  ACCESS read-only
  STATUS mandatory
  DESCRIPTION "fractions of seconds as a count of 15.25ns pulses"
  ::={syslogEntry 2}

  eventid OBJECT-TYPE
  SYNTAX INTEGER (1..2147483647)
  ACCESS read-only
  STATUS mandatory
  DESCRIPTION "Event log index"
  ::={syslogEntry 3}

  severity OBJECT-TYPE

«
...
48
49
50
51
52
...
»

Содержание NTP80plus


























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды