Textron Greenlee Communications DataScout 10G страница 60 Скачать руководство пользователя | Manualshive

Страница: 60 / 115

background image

58

Test Interface Connections

To connect the test interface to the device under test you must select the proper patch
cable depending on which interface you are testing and the termination type if using
the optical ports. There is no specific order of connection required. You can connect
the patch cord to the test device or network device first.

Impedance Selection

2-wire signaling supports voice-band 600, 900 and 1200

Ω impedances. 4-Wire signal-

ing also supports the impedances plus 100 (T1) and 135

Ω (DDS). To change receive

and transmit impedances, tap on the impedance pull-down menu and select the de-
sired impedance. The RCV and XMT are always the same impedance.

Some features are enabled or disabled based on impedance and 2/4 Wire selection i.e.
600, 900, 1200 are voice-band impedances and will enable voice-band test features.
100 & 135 Ohm are wideband impedances and will enable wideband features.

Signaling Mode Selection

Upon selection of 2-wire Signaling defaults to LS-Loop-Start Station signaling mode.
To change signaling modes simply tap on Station (PBX). Tap the desired Emulation
(CO/PBX) and Signaling type (LS, GS, E&M I-V, DID and DID-wink, Selective Signal-

«
...
58
59
60
61
62
...
»

Содержание Greenlee Communications DataScout 10G




















































































































Отзывы:

Нет отзывов

Похожие инструкции для Greenlee Communications DataScout 10G

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: IBEX Страницы: 4

Бренд: Landoll Страницы: 70

Бренд: Landice Страницы: 19

Бренд: Landice Страницы: 7

Бренд: Kattsafe Страницы: 19

Бренд: Raytec Страницы: 8

Бренд: PMK Страницы: 24

Бренд: SteelFlex Страницы: 13

Бренд: ZOE Страницы: 40

Бренд: Danfoss Страницы: 20

ParaPost XT P-680T

Бренд: Coltene Страницы: 44

ASTRORIDE A6.0 BIKE

Бренд: Reebok Страницы: 23

Бренд: Paloma Страницы: 12

Aesculap activ C

Бренд: Braun Страницы: 41

CoverPro 3000 PROFESSIONAL

Бренд: Janome Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды