Textron Greenlee Communications DataScout 10G страница 24 Скачать руководство пользователя | Manualshive

Страница: 24 / 115

background image

22

Charge, Wi-Fi & Remote Management Interfaces

Charge, Wi-Fi & Remote Management Interfaces

1. Charger input is located in the upper left corner and is labeled 9V. Only use the

approved Greenlee Communications supplied charger as other models may dam-
age the internal power supply and will void the warranty.

2. RJ45 Ethernet port enables full remote control of the test set when the DS10-SW-

RC option is enabled.

3. OTG (On-the-Go) Micro-AB USB port is to connect to your PC in order to perform

application updates or copy/delete documents and save test results.

4. Two USB type-A ports are used to connect a variety of USB accessories such as

flash drives, monitor or keyboards/mice. Do not use the USB for charging external
products or accessories.

LCD Display

The test set is equipped with a bright

7” color tablet LCD enabling test results, web

pages, documents and office applications to be easily viewed, even in bright sunlight.

Portrait & Landscape Modes

The unit defaults to landscape display orientation upon power on. To change to por-
trait mode simply tap the

portrait

button in the upper right of the test screens to display

the screen in portrait mode. This button will change to say

landscape

when in portrait

mode.

Proper Care

Always use clean fingers or a touch screen stylus when interacting with the touch
screen. Never use hard objects such as screw drivers, knives, or pen tips as they may
damage the LCD screen. To clean the LCD use a cloth lightly dampened with clean
water only.

Failure to follow any of the above could result in permanent damage to the LCD and
void the warranty.

«
...
22
23
24
25
26
...
»

Содержание Greenlee Communications DataScout 10G




















































































































Отзывы:

Нет отзывов

Похожие инструкции для Greenlee Communications DataScout 10G

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: Laica Страницы: 4

Бренд: Taylor Страницы: 70

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: Oberheim Страницы: 40

Бренд: Zenbooth Страницы: 60

Бренд: jablotron Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: Samson Страницы: 2

Бренд: GE Страницы: 2

Monolith NT.115

Бренд: Nano Temper Страницы: 24

SCAFFOLDBENCH I-CISRL

Бренд: MetalTech Страницы: 16

Be strong NS 200X

Бренд: Nautilus Страницы: 27

Бренд: TaiShan Страницы: 5

NESLAB System IV

Бренд: Thermo Scientific Страницы: 22

Бренд: QTX Light Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды