manualshive.com logo in svg

TEXIO PSF-400H, Инструкция по эксплуатации

Поделиться
Скачать
TEXIO PSF-400H Скачать руководство пользователя страница 58

 

 

48

6 OTHER FUNCTIONS 

6-1. Display in alarm status 

When the PSF Series power supply unit enters the alarm status or the function 
described in Section 

”5-7-5. Alarm function using external contacts”

 is used, 

the alarm code shown below is displayed, indicating that an alarm occurs in the 
power supply unit.  When an alarm occurs, the power supply unit turns off 
output and stays in the alarm status.    When a protection function (excluding 
OVP and OCP described in Section 

“5-5-2. OVP/OCP function (02)” 

works, all 

operations (panel operation, etc.) are disabled and the power supply unit stops 
operation. 

Press the ESC/DISP key for one second to reset the OVP or OCP alarm 
(described in Section 

 “5-5-2. OVP/OCP function (02)”

) Turn off the input 

power source or shut off the POWER switch and throw it again to reset the 
protection function. 

 

 

Type of alarm

 

Display Description

 

OVP alarm 

This alarm code is displayed if the output voltage 
exceeds the preset OVP value. 

OCP alarm 

This alarm code is displayed if the output current 
exceeds the preset OCP value. 

OHP alarm 

The OHP alarm is displayed if the temperature at the 
internal detection point exceeds the set temperature.  
The displayed alarm differs with the models as shown 
below. 

Over-voltage (OVP) 

Output is turned off if the 
voltage exceeds 110% of the 
rated output voltage. 

Over-current (OCP) 

Output is turned off if the 
current exceeds 110% of the 
rated output current. 

HARD alarm 

Alarm using external   
contacts ALARM 

Alarm is caused when the 
contacts are short- 
circuited.   

◆

  For details, see section   

”5-7-5. Alarm function 
using external contacts”

 

above. 

Содержание PSF-400H































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды