Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 91

Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 84

Technical Reference Manual

TMDXEVM6657L

SPRUHG7 - Revised August 2012

TMDXEVM6657LE

Page 84 / 90

4

DSP_RESETSTAT#:

This bit reflects the DSP_RESETSTAT# state.

0: DSP_RESETSTAT# state is low
1: DSP_RESETSTAT# state is high

RO

5

TRGRSTZ:

This bit reflects the TRGRSTZ state.

0: TRGRSTZ state is low
1: TRGRSTZ state is high

RO

6

PCIESSEN:

This bit reflects the PCIESSEN switch state.

0 : PCIESSEN state is low
1 : PCIESSEN state is high

RO

7

User_Defined Switch:

This bit reflects the User_Define Switch state.

0 : User_Defined Switch state is low
1 : User_Defined Switch state is high

RO

Register Address:

SPI Base + 0Ch

Register Name:

Miscellaneous - 1 Register

Default Value:

1Ch

Attribute:

Read/Write

Bit

Description

Read/Write

1-0

McBSP_AMC_EN#:

These bits can be updated by the DSP software to

drive values on the McBSP_AMC_EN# pin and for selection of TCLK for
McBSP
00: Drive McBSP_AMC_EN# low.
  Connect TCLKA to McBSP SLCLKs, TxCLKs & RxCLKs.
  Connect TCLKC to McBSP FSTs & FSRs.
01: Drive McBSP_AMC_EN# low.
  Connect TCLKB to McBSP SLCLKs, TxCLKs & RxCLKs. (RFU).
  Connect TCLKC to McBSP FSTs & FSRs.
10: Drive McBSP_AMC_EN# low.
  Connect TCLKD to McBSP SLCLKs, TxCLKs & RxCLKs. (RFU)
  Connect TCLKC to McBSP FSTs & FSRs.
11: Drive McBSP_AMC_EN# high.
  Output SLCLKs, TxCLKs, RxCLKs, FSTs, FSRs as (Hi Z)

R/W

2

NAND_WP# :

This bit can be updated by the DSP software to drive a

high or low value on the NAND_WP# pin
0 : NAND_WP# drives low
1 : NAND_WP# drives high

R/W

3

XDS560_IL control

0 : Disable XDS560 mezzanine card
1 : Enable XDS560 mezzanine card (Default)

R/W

4

NOR_WP# :

This bit can be updated by the DSP software to drive a

high or low value on the NOR_WP# pin
0 : NOR_WP# drives low
1 : NOR_WP# drives high

R/W

5

EEPROM_WP:

This bit can be updated by the DSP software to drive a

high or low value on the EEPROM_WP pin
0 : EEPROM_WP drives low
1 : EEPROM_WP drives high

R/W

«
...
82
83
84
85
86
...
»

Содержание eInfochips TMDXEVM6657L




























































































Отзывы:

Нет отзывов