Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 91

Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 60

Technical Reference Manual

TMDXEVM6657L

SPRUHG7 - Revised August 2012

TMDXEVM6657LE

Page 60 / 90

delay

time

is

set

by

UCD9222

configuration file.

5

VCC1V8 (DSP IO power)

5ms

Turn on VCC1V8 after VCC1V0 is stable
for 5ms.

6

CDCE62005#2 initiations
FPGA 1.8V outputs

5ms

Unlock

1.8V

outputs

and

initiate

CDCE62005 after VCC1V8 is stable for
5ms by de-asserting power down (PD#)
pins.

7

VCC1V5 (DSP DDR3 power)

5ms

Turn on VCC1V5 5ms after the initiation
of CDCE62005.

8

VCC0V75

5ms

Turn on VCC0V75 after VCC1V5 is stable
for 5ms.
When VCC1V5 is valid, FPGA de-asserts
the power down pin of IDT5V41068, PCIe
clock multiplexor.
When VCC0V75 is valid, FPGA enables
mux clock outputs asserting OE pin.

9

RESETz
Other reset and NMI pins

5ms

De-asserts  RESETz  and  unlocks  other
reset  and  NMI  pins  for  DSP  after
VCC0V75  is  stable  and  CDCE62005  PLL
locked for 5ms.
In  the  meanwhile,  FPGA  will  drive  the
boot configurations to DSP GPIO pins.

10

PORz

5ms

De-asserts PORz after RESETz is de-
asserted for 5ms.

11

RESETFULLz

5ms

De-asserts RESETFULLz after PORz is
de-asserted for 5ms.

12

DSP GPIO pins for boot
configurations

1ms

Releases

DSP

GPIO

pins

after

RESETFULLz is de-asserted for 1ms

Power-Down

13

RESETFULLz
PORz

0ms

If there is a power failure or AMC payload
is

powered

off,

FPGA

will

assert

RESETFULLz and PORz signals to DSP.

14

FPGA 1.8V outputs
CDCE62005 PD# pins

5ms

Locks 1.8V output pins on FPGA and pull
CDCE62005 PD# pin to low to disable
DSP clocks

15

CVDD
VCC1V0
VCC1V8
VCC1V5
VCC0V75
VCC2V5
IDT5V41068 PD# and OE

0ms

Turns off all main power rails.

«
...
58
59
60
61
62
...
»

Содержание eInfochips TMDXEVM6657L




























































































Отзывы:

Нет отзывов