Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 91

Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 28

Technical Reference Manual

TMDXEVM6657L

SPRUHG7 - Revised August 2012

TMDXEVM6657LE

Page 28 / 90

2.6 I2C Boot EEPROM / SPI NOR Flash

The I2C modules on the TMS320C6657 may be used by the DSP to control local peripheral ICs (DACs, ADCs,
etc.) or may be used to communicate with other controllers in a system or to implement a user interface.

The  I2C  bus  is  connected  to  one  EEPROM  and  to  the  80-pin  expansion  header  (TEST_PH1).  There  are  two
banks in the I2C EEPROM which respond separately at addresses 0x50 and 0x51. These banks can be loaded
with  demonstration  programs.  Currently,  the  bank  at  0x50  contains  the  I2C  boot  code  and  PLL  initialization
procedure  and  the  bank  at  0x51  contains  the  second  level  boot-loader  program.  The  second  level  boot-loader
can be used to either run the POST program or launch the OOB demonstration from NOR flash memory.

The Serial Peripheral Interconnect (SPI) module provides an interface between the DSP and other SPI-compliant
devices. The primary intent of this interface is to allow for connection to a SPI ROM for boot. The SPI module on
TMS320C6657 is supported only in Master mode.

16MB  NOR  FLASH  (part  number  N25Q032A11  from  NUMONYX)  is  attached  to  CS0z  on  TMS320C6657.  It
contains demonstration programs such as POST or OOB demo. The CS1z of SPI is used by the DSP to access
registers within FPGA.

DSP

(C6657)

SPI

16MB NOR Flash

(N25Q032A11ESE40F)

4

4

FPGA

XC3S200AN

80-pin Expansion

Header

4

CS1

CS0

4

CS1

Figure 2.4: C6657 Lite EVM Clock Domains

«
...
26
27
28
29
30
...
»

Содержание eInfochips TMDXEVM6657L




























































































Отзывы:

Нет отзывов