Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 91

Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 36

Technical Reference Manual

TMDXEVM6657L

SPRUHG7 - Revised August 2012

TMDXEVM6657LE

Page 36 / 90

2.16 Module Management Controller (MMC) for IPMI

The C6657 Lite EVM supports limited set of Intelligent Platform Management Interface (IPMI) commands using
Module Management Controller (MMC) based on Texas Instruments MSP430F5435 mixed signal processor.

The MMC will communicate with MicroTCA Carrier Hub (MCH) over IPMB (Intelligent Platform Management Bus)
when inserted into AMC slot of a PICMG® MTCA.0 R1.0 compliant chassis. The primary purpose of the MMC is
to  provide  necessary  information  to  MCH,  to  enable  the  payload  power  to  C6657  Lite  EVM  EVM  when  it  is
inserted into the MicroTCA chassis.

The  EVM  also  supports  a  Blue  LED  and  LED1  on  the  front  panel  as  specified  in  PICMG®  AMC.0  R2.0
AdvancedMC base specification. Both of these LEDs will blink as part of initialization process when the MMC will
receive management power.

Blue LED (D2):

Blue LED will turn ON when MicroTCA chassis is powered ON and an EVM is inserted into it. It will turn
OFF when payload power is enabled to the EVM by the MCH.

RED LED (D1):

This Red colored LED will normally be OFF. It will turn ON to provide basic feedback about failures and
out of service conditions.

FPGA

(XC3S200AN)

DSP

(C6657)

DSP Rst

Events

MMC_EN#

AMC

CON

MMC

(MSP430F5435)

(1.8V)

PORz
RSTFULLz
RESETz

CoreSel[1:0]
NMIENz

RSTSTATz
BOOTCOMP

DSP RSTSTAT#

DSP BOOTCOMP

MMC_RSTSTAT#

MMC_BOOTCOMP

MMC_DETECT#

MMC_POR_AMC#

MMC_WR_AMC#

(3.3V)

IPMB-L (I2C)

GA[2:0]

(3.3V)

(3.3V)

(1.8V)

Figure 2.15: C6657 Lite EVM MMC Connections for IPMI

2.17 Expansion Header

The C6657 Lite EVM contains 80 pin header (TEST_PH1) which has UPP (EMIF), McBSP[1:0], TIMI[1:0],
TIMO[1:0], I2C, SPI, GPIO[15:14] and UART signal connections. It shall be noted that all signals to this header
are of 1.8V level.

«
...
34
35
36
37
38
...
»

Содержание eInfochips TMDXEVM6657L




























































































Отзывы:

Нет отзывов