Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 91

Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 83

Technical Reference Manual

TMDXEVM6657L

SPRUHG7 - Revised August 2012

TMDXEVM6657LE

Page 83 / 90

4

MMC_BOOTCOMP:

This bit reflects DSP BOOTCOMPLETE state and

FPGA will drive the same logic value on the MMC_BOOTCOMP pin (to
MMC).
0: State is low and FPGA drives MMC_ BOOTCOMP low to MMC
1: State is high and the FPGA drives MMC_ BOOTCOMP high to MMC

RO

7-5

Reserved

RO

Register Address:

SPI Base + 0Ah

Register Name:

PHY Control Register

Default Value:

03h

Attribute:

Read/Write

Bit

Description

Read/Write

0

PHY_INT#:

This bit reflects the PHY_INT# state.

0: PHY_INT# state is low.
1: PHY_INT# state is high.

RO

1

PHY_RST:

This bit can be updated by the DSP software to drive a high

or low value on the PHY_RST pin
0: PHY_RST drives low
1: PHY_RST drives high

R/W

7-2

Reserved

RO

Register Address:

SPI Base + 0Bh

Register Name:

Reset Button Status Register

Default Value:

--------

Attribute:

Read Only

Bit

Description

Read/Write

0

FULL_RESET Button Status:

This bit reflects the FULL_RESET button

state. This button is used to request a power full reset sequence to
DSP. A logic Low to High transition on this button signal will complete
the FPGA FULL_RESET sequence with a specified delay time.
0: FULL_RESET button state is low
1: FULL_RESET button state is high

RO

1

WARM_RESET Button Status:

This bit reflects the WARM_RESET

button state. This button is used to request a warm reset sequence to
DSP. A logic Low to High transition on this button signal will complete
the FPGA WARM_RESET sequence with a specified delay time.
0: WARM_RESET button state is low
1: WARM_RESET button state is high

RO

2

COLD_RESET Button Status (RFU):

This bit reflects the COLD

_RESET button state. Not used in current implementation.
0: COLD_RESET button state is low
1: COLD_RESET button state is high

RO

3

FPGA_JTAG_RST#

0: FPGA_JTAG_RST# state is low
1: FPGA_JTAG_RST# state is high

RO

«
...
81
82
83
84
85
...
»

Содержание eInfochips TMDXEVM6657L




























































































Отзывы:

Нет отзывов