Texas Instruments DRV10963 Скачать руководство пользователя страница 1

Страница: 1 / 29

User's Guide

SLAU643 – July 2015

DRV10963 Evaluation Module

This document is provided with the DRV10963 customer evaluation module (EVM) as a supplement to the
DRV10963 datasheet (

SLAS955

A). It details the hardware implementation of the EVM and gives a step-

by-step introduction to the device operation and tuning process using DRV10963 GUI.

Contents

DRV10963 EVM Kit Contents

..............................................................................................

Introduction

...................................................................................................................

DRV10963 Motherboard Connectors

.....................................................................................

3.1

Power Input

..........................................................................................................

3.2

Interface Connectors to Mount Daughterboard P1, P2

........................................................

3.3

USB to Any Connector

.............................................................................................

DRV10963 Daughterboard Connectors

...................................................................................

4.1

Motor Output Connector

...........................................................................................

4.2

Interface Connectors to Motherboard P1, P2

...................................................................

Quick Start Guide

............................................................................................................

5.1

Installation of Software

.............................................................................................

5.2

Initial Hardware Settings

...........................................................................................

5.3

Jumpers and Switch Setup Settings

.............................................................................

5.4

Powering-Up EVM

..................................................................................................

5.5

Tuning GUI: to Configure Motor Parameter

.....................................................................

Tuning Guide

................................................................................................................

6.1

Configuring the Device

...........................................................................................

6.2

Writing to the OTP Registers

....................................................................................

6.3

Reading the OTP Values

.........................................................................................

6.4

Notes

................................................................................................................

Schematic and Bill of Materials

...........................................................................................

7.1

Schematic

..........................................................................................................

7.2

Bill of Materials (BOM)

............................................................................................

List of Figures

DRV10963 Motherboard with Socket Daughterboard Mounted on top

...............................................

DRV10963 Daughterboard Mounting on Motherboard

.................................................................

DRV10963 Orientation Inside Daughterboard Socket

..................................................................

GUI Initial Screen With Demo Mode

.....................................................................................

GUI Screen With Successful I2C Interface

..............................................................................

Default Configuration Parameters

........................................................................................

Loading DRV10963JM Configuration Parameter to Device

..........................................................

DRV10963JM Configuration Parameter

................................................................................

Initial Tuning Flow Chart

...................................................................................................

Error Message

..............................................................................................................

Correct Align Time and Acceleration Rate

..............................................................................

Align Time Too Long

.......................................................................................................

Align Time Too Short

......................................................................................................

Open to Close Loop Threshold Too Low

................................................................................

SLAU643 – July 2015

DRV10963 Evaluation Module

Submit Documentation Feedback

Содержание DRV10963






























Результаты поиска

Содержание DRV10963

Отзывы:

Похожие инструкции для DRV10963

Бренды по названию

Популярные бренды

Texas Instruments DRV10963, Руководство пользователя

Результаты поиска

Содержание DRV10963

Отзывы:

Похожие инструкции для DRV10963

Бренды по названию

Популярные бренды