Tews Technologies TPMC851 Скачать руководство пользователя страница 39

Страница: 39 / 65

ADC Sequencer Data RAM

3.3

PCI Base Address:

PCI9030 PCI Base Address 3 (Offset 0x1C in PCI Configuration Space).

The ADC Sequencer Data RAM is a 32 x 16 bit wide RAM storing the converted data values.

Each channel has its own ADC Data location.

The ADC Sequencer Data RAM is updated after every full sequencer cycle. Only the channels enabled in the
ADC Sequencer Instruction RAM are updated.

Offset to PCI Base
Address 3

Description

Size
(Bit)

0x00

Channel 1 ADC Sequencer Data

0x02

Channel 2 ADC Sequencer Data

…

0x3C

Channel 31 ADC Sequencer Data

0x3E

Channel 32 ADC Sequencer Data

Table 3-33: ADC Sequencer Data RAM Space Address Map

ADC/DAC Calibration Data ROM

3.4

PCI Base Address:

PCI9030 PCI Base Address 4 (Offset 0x20 in PCI Configuration Space).

The calibration data values are determined at factory and stored in this ROM space.

There is one Offset Error value and one Gain Error value for each ADC gain which are valid for all 32 channels.
For the DACs again there is an Offset Error value and a Gain Error value for each DAC channel.

See the Programming Hints chapter for data correction formulas.

The calibration data is read only.

The calibration data is available 500 μs after reset.

Offset to PCI Base
Address 4

Description

Size
(Bit)

0x00

ADC Offset

ERROR

Gain 1

0x02

ADC Gain

ERROR

Gain 1

0x04

ADC Offset

ERROR

Gain 2

0x06

ADC Gain

ERROR

Gain 2

0x08

ADC Offset

ERROR

Gain 4

0x0A

ADC Gain

ERROR

Gain 4

0x0C

ADC Offset

ERROR

Gain 8

0x0E

ADC Gain

ERROR

Gain 8

0x10

DAC Channel 1 Offset

ERROR

0x12

DAC Channel 1 Gain

ERROR

0x14

DAC Channel 2 Offset

ERROR

0x16

DAC Channel 2 Gain

ERROR

TPMC851 User Manual Issue 1.0.9

Page 39 of 65

Содержание TPMC851


































































Результаты поиска

Содержание TPMC851

Отзывы:

Похожие инструкции для TPMC851

Бренды по названию

Популярные бренды

Tews Technologies TPMC851, Руководство пользователя

Результаты поиска

Содержание TPMC851

Отзывы:

Похожие инструкции для TPMC851

Бренды по названию

Популярные бренды