TESA Auto lift system Скачать руководство пользователя страница 3

Страница: 3 / 21

Important remarks

Please read attentively this manual with its detailed information also after the

correct. The manufacturer is not responsible for damages and injuries caused by

incorrect installation and use of the system.

Use fixing points with sufficient stability. Consider every
jack can lift up to 2500 kg. If necessary the fixing points at
the chassis must reinforced with adequate parts.

Consider the required space between jack and floor of
35mm at least in vertical position

Do not forget to install the fuse in the +power line and
make sure a professional execution of electrical works to
guarantee the safety functions

Follow the instructions step by step and complete the
chapter “Initial operation” after installing.

Содержание Auto lift system






















Результаты поиска

Содержание Auto lift system

Отзывы:

Похожие инструкции для Auto lift system

Бренды по названию

Популярные бренды

TESA Auto lift system, Руководство по установке и эксплуатации

Результаты поиска

Содержание Auto lift system

Отзывы:

Похожие инструкции для Auto lift system

Бренды по названию

Популярные бренды