Teo 6220-TSG-DD Скачать руководство пользователя страница 14

Страница: 14 / 48

Tone Commander 6220-TSG-DD Installation Instructions

Page 14

13-280121 Rev. C

Wall Mounting _______________________________________________

Robust handset retainer clips for wall mount use are available on request from Tone Commander.

Rotating the Base

The phone base must be rotated for wall mounting.

•

Disconnect the line cord.

•

Remove the retaining screw in the center of the base.

•

Press the top of the tall edge of the base to disengage the snap tabs, and then lift the base from the

telephone body.

Do not touch the expansion connector. If using the 6030X or 6002TA, leave the expansion cable

plugged into the phone.

•

Turn the base 180°, insert the tabs on the short edge of the base into the holes near the display end of

the telephone, and then snap the tall side of the base onto the telephone.

•

Replace the retaining screw (required for UL compliance).

Attaching to a wall mount jack

Note

: The TSG-DD1 Disconnect Device must be connected in series with the ISDN line (page 12).

•

6220T-TSG-DD: Plug the line cord from the

TO PHONE

jack on the TSG-DD1 into the

S/T IN

jack on

the telephone. Route the cord under the guide tabs on the base. Connect an 8-conductor line cord

between the

TO LINE

jack on the TSG-DD1 and the wall jack.

Plug the supplied Tone Commander -PWR1 Desktop Power Supply into the 48 VDC jack on the TSG-

DD1.
6220U-TSG-DD: Plug the line cord from the

TO PHONE

jack on the TSG-DD1 into the

U IN

jack on the

telephone. Route the cord under the guide tabs on the base. Connect an 8-conductor line cord between

the

TO LINE

jack on the TSG-DD1 and the wall jack.

Plug the supplied Tone Commander -PWR1 Desktop Power Supply into the 48 VDC jack on the TSG-

DD1.

Do not connect the power supply directly to the phone.

•

Hang the telephone on the wall plate mounting studs. Press down firmly to lock in place.

The phone can also be mounted directly to the wall with screws, and connected to a line jack or to the

TSG-DD1 with the supplied line co

Содержание 6220-TSG-DD

















































Результаты поиска

Содержание 6220-TSG-DD

Отзывы:

Похожие инструкции для 6220-TSG-DD

Бренды по названию

Популярные бренды

Teo 6220-TSG-DD, Руководство по установке

Результаты поиска

Содержание 6220-TSG-DD

Отзывы:

Похожие инструкции для 6220-TSG-DD

Бренды по названию

Популярные бренды