Teo 6220-TSG-DD Скачать руководство пользователя страница 12

Страница: 12 / 48

Tone Commander 6220-TSG-DD Installation Instructions

Page 12

13-280121 Rev. C

U Version (6220U-TSG-DD) Installation __________________________

This model includes a built-in NT1. Optional external ISDN S/T Terminal Equipment may share the

telephone's ISDN line by connecting to the

S/T OUT

jack on the telephone, which supplies PS1 and PS2

output power.
If you are not using external Terminal Equipment, no termination switch setting is required.

Connect the Handset

•

Plug the supplied handset into the jack on the left side of the telephone. Refer to page 7, item 17.

Line and Power Connections __________________________________

The TSG-DD1 disconnect device completely disconnects the ISDN line when power is not applied. It is

installed in series with the phone’s line cord.

•

Clip the ends off of the retainer tabs on the cord that connects the TSG-DD1 to the phone, to prevent

the TSG-DD1 from being disconnected from the phone.

Clip the tabs as shown; do not completely

remove the tabs!

•

Install the TSG-DD1 in series with the phone’s line cord as shown on the following page.

For the S/T version (6220T-TSG-DD), connect the

S/T IN

jack on the telephone to the

TO PHONE

jack

on the TSG-DD1, using an 8-conductor line cord.
For the U version (6220U-TSG-DD), connect the

U IN

jack on the telephone to the

TO PHONE

jack on

the TSG-DD1, using an 8-conductor line cord.

•

Plug the supplied Tone Commander -PWR1 Desktop Power Supply into the 48 VDC jack on the TSG-

DD1.

Do not connect the power supply directly to the phone.

Содержание 6220-TSG-DD

















































Результаты поиска

Содержание 6220-TSG-DD

Отзывы:

Похожие инструкции для 6220-TSG-DD

Бренды по названию

Популярные бренды

Teo 6220-TSG-DD, Руководство по установке

Результаты поиска

Содержание 6220-TSG-DD

Отзывы:

Похожие инструкции для 6220-TSG-DD

Бренды по названию

Популярные бренды